background image

Page 2 of 6

Prior to removing the pivot bushing, assemble the removal 

tool correctly.

For this purpose, assemble the components as shown in 
figure 2, Screw the Ram (3), Ram Adapter (8), Ram Extension 
(9) and Threaded Rod (4) together in that order, attach 
the Cover Plate (7) over the Ram Extension, then slide the 
Receiver Tube over (5) the Threaded Rod.

Fig. 2 - Assembled Removal Tool

! IMPORTANT

When assembling the removal tool, always make sure that 
the receiver tube end (5) with out a centering ring faces 
toward the cover plate. The centering ring(Fig.3) of the 
receiver tube is used to center the receiver tube on the 
trailing arm receptacle. When the removal tool is used, the 
centering ring must always face toward the trailing arm 
receptacle.

Fig. 3 - Receiver tube with centering ring

Centering Ring

REMOVAL

Fig. 1 - Identification of removal tool components

Preparing the Pivot Bush 
Replacement Tool

The pivot bushing removal tool (here after 

abbreviated to removal tool) consists of:

(1) 

Enerpac hydraulic actuator

(2) 

Hydraulic connecting hose

(3) 

Hydraulic ram

(4) 

Threaded rod

(5) 

Receiver tube

(6) 

Drive nut

(7) 

Cover plate

(8) 

Ram adapter

(9) 

Ram extension

1

2

3

4

5

6

7

8

9

Summary of Contents for 3 434 3317 00







Reviews: