Saeco PRIMEA LINE 2007 Technical & Service Manual Download

Page: 45 / 79

REV. 00 - Mar. 07

Ring andTouch multi-way valve opening operating diagram

2/9

PRIMEA 2007 Chapter 06

wo f

actors combine to giv

e the fiv

e phases of the multiw

alv

1) Activ

ation (or not) of two micr

oswitches on the multiv

alv

2) Dir

ection of rotation of the multiv

alv

Heater

Multi-way

Autocappuccino valve

Cappuccino maker

Milk container

Heater

Pressblock

3 2 1

PHASE -2

STEAM /

AUTORINSE

PHASE -1

MICRO

DRAIN

PHASE 0

MICRO 1 and 2

DRAIN

UNIT

PHASE +2

MICRO 1

HOT WATER

PHASE +1

MICRO 2

COFFEE

MICRO

steam outlet for boiler drainage

hot water inlet from water boiler

hot water to brew unit to make coffee

hot water to dispense pipe

steamout

uv=

outlet closed

sg=

unit water drain

Pos.1

Pos.2

Pos.3

Pos.4

Pos.5

Dissipater

Pressblock

BOILER DRAIN

After steam production (e.g: cappuccino) the boiler drain discharges steam into the drip tray with cooling via the dissipater.

The boiler is re-loaded to enable delivery of coffee or water.

MICRO 1

MICRO 2

AUTORINSE

Summary of Contents for PRIMEA LINE 2007
















































































Search results

Summary of Contents for PRIMEA LINE 2007

Reviews:

Related manuals for PRIMEA LINE 2007

Brands by name

Popular brands

Saeco PRIMEA LINE 2007, Technical & Service Manual

Search results

Summary of Contents for PRIMEA LINE 2007

Reviews:

Related manuals for PRIMEA LINE 2007

Brands by name

Popular brands