background image

 

3

USING YOUR 

MaxiMixer

 

 

READ CAREFULLY 

 

SETUP

  

 
1.  When you are delivered your new 

MaxiMixer

 from the factory, it is not immediately necessary 

to check the machine for bearing lubrication or chain tightness, as these items have been factory 
serviced.  It is recommended to walk around the machine and familiarize yourself with the 
location of all moving parts, caution decals, the general operating dimensions, and the basic 
working features of the 

MaxiMixer

 

CAUTION!

 BEFORE OPERATING THIS MACHINE, READ AND 

UNDERSTAND THIS OWNER'S MANUAL AND ALL CAUTION, 
WARNING, AND DANGER SYMBOLS LOCATED ON THE 
MACHINE AND IN THIS MANUAL.            

 

 
2.  All lubrication has been completed at the factory prior to delivery and will not be immediately 

necessary. For Lubrication intervals and specifications see the enclosed Lubrication Schedule.  

 

IMPORTANT! DO NOT OVER GREASE BEARINGS, SEAL FAILURE AND 
SUBSEQUENT PREMATURE BEARING FAILURE COULD RESULT.

  

 
3.  When you receive your 

MaxiMixer

, it will be first necessary for you to hook up the power 

source for the solenoid that switches power between the hydraulic functions (if so equipped).  
The switch box is supplied with a lead that has 1 white wire and 1 black wire.  The white wire 
is to be hooked to positive and the black is to be hooked to ground.  It is recommended to hook 
these leads into a switched power source such as a keyed ignition.  This will eliminate the 
possibility of draining the battery if the switch is left on. When not in use, be sure to turn unit 
off. 
 

IMPORTANT: ALWAYS KEEP POWER CONNECTIONS TIGHT, NEAT AND FREE 
FROM DIRT AND CORROSION!  DO NOT HOOK THE LEADS FOR THE SWITCH 
BOX INTO THE MIXER MOUNTED BATTERY THAT SUPPLIES THE SCALE! 

 

 

The leads for the switch box have been supplied with and inline fuse holder that holds a 10 amp 
fuse. 

 
CAUTION!

 DO NOT REPLACE A BLOWN FUSE WITH A FUSE OF A 

HIGHER RATING!  

 

 

 

 

Summary of Contents for MaxiMixer 2030






















































Reviews: