background image

 

5

 
 

OPERATION 

 
1.  Before attempting to fill the mixer, make sure that the discharge door is completely closed, the 

chute is in the up position, and the mixing chamber is free of any foreign objects. 

 

IMPORTANT! IF THE DISCHARGE DOOR IS LEFT OPEN DURING MIXING,         
FEED MAY BECOME TIGHTLY PLUGGED AGAINST THE CONVEYOR AND 
DAMAGE IT.                               

 

2.  Refer to the Owner's Manual of the tractor before operating the mixer, to ensure proper PTO 

engagement. 

 
 

CAUTION:

 Use 540 rpm only. Avoid high  speed  engagement  of             

       the 

MaxiMixer

 as it could cause the shear pin to shear or damage the 

drive system.

 

 
 

3. The 

MaxiMixer

 will effectively mix all ingredients in a Total Mixed Ration including small 

grains, corn, concentrates and premixes, cotton seed, corn and hay silage etc.  The 

MaxiMixer

 

is also capable of processing dry long stem hay into your ration.  It is not recommended that 
wrapped and ensiled round bales be processed in the 

MaxiMixer

 

 

      

IMPORTANT! THE MIXER SHOULD ALWAYS STAND LEVEL WHEN MIXING!

 

 
4.  Due to the nature of mixing and cutting long stem hay, pin shearing is something that can be 

expected.  The shear pin is designed to be the weakest link in the drive train and its shearing is 
to prevent damage to critical components.  Therefore never replace shear pins with a higher 
tensile strength or grade pin.  If a machine is regularly shearing pins, the operator should first 
look for mechanical problems such as worn knives or a bearing failure, then evaluate loading 
procedures and lastly, call for technical assistance. 
 

5. If a 

MaxiMixer

 does become plugged or jammed to the point where normal mixing rotation 

(counter clockwise from the front) will not resolve the problem, it will be necessary to reverse 
the mixer.  This can safely be done by first turning off all power sources, setting the parking 
brake and waiting for all motion to stop before removing the PTO from the input shaft end.  
Then fit the supplied T handle to the input shaft, and then turn the T handle (facing the mixer) 
clockwise to loosen the plugged material.  

 

 

DANGER!  TO PREVENT SERIOUS INJURY OR DEATH, DO NOT 
ENTER THE MIXING CHAMBER!                           

 

 

 

Summary of Contents for MaxiMixer 2030






















































Reviews: