background image

Page 23

The model number will be found on a plate attached to the base. Always mention the model number in all correspondence regarding your SCROLL
SAW 
or when ordering repair parts.

RYOBI 16 in. SCROLL SAW – MODEL NUMBER SC155VS

SEE BACK PAGE FOR PARTS ORDERING INSTRUCTIONS

PARTS LIST FOR FIGURE B

Key Part
No.

Number

Description

Quan.

Key  Part
No.

Number

Description

Quan.

1

102039004

Table Screw ............................................................ 1

2

105015009

Table ........................................................................ 1

3

190030500

* Screw (M5 x 8 Pan Hd.) .......................................... 3

4

979766001

Screw (M4 x 16 Pan Hd.) ........................................ 2

5

168041001

Warning Label ......................................................... 1

6

981365001

Cover Plate .............................................................. 1

7

981369001

Nozzle ...................................................................... 1

8

300305015

* Hex Bolt (M5 x 16) ................................................... 3

9

Incl w/#8

Washer (M5) ............................................................ 3

10

981362001

Base ........................................................................ 1

11

981363001

Data Plate ................................................................ 1

12

979791001

Strain Relief ............................................................. 1

13

979790001

Cord Assembly ........................................................ 1

14

981377001

Motor Cover ............................................................. 1

15

981378001

Screw (M5 x 12 Pan Hd.) ........................................ 5

16

981375001

Control Box Cover ................................................... 1

17

981372001

PC Board Assembly ................................................ 1

18

979798001

Gasket ..................................................................... 1

19

981376001

Control Box .............................................................. 1

20

981373001

Switch Knob ............................................................ 1

21

981370001

Switch Label ............................................................ 1

22

981371001

Screw (M5 x 9 Pan Hd.) .......................................... 3

23

981396001

Brush Assembly ....................................................... 2

24

981374001

Screw (M4 x 15 Pan Hd.) ........................................ 2

25

981397001

Brush Cap ............................................................... 2

26

980123001

Motor Assembly ....................................................... 1

27

350308161

* Spring Washer (M8) ................................................ 2

28

360308000

* Lock Washer (M8) ................................................... 2

29

100308020

Screw (M8 x 25 Hex Hd.) ........................................ 2

30

981364001

Table Support .......................................................... 1

31

160030400

* Screw (M4 x 8 Pan Hd.) .......................................... 3

32

981379001

Star Washer (M5) .................................................... 1

33

100030501

* Screw (M5 x 15 Pan Hd.) ........................................ 4

34

360305000

* Lock Washer (M5) ................................................... 7

35

981367001

Spacer ..................................................................... 3

36

104022003

Pointer ..................................................................... 1

37

190030500

* Screw (M5 x 8 Pan Hd.) .......................................... 3

38

981361001

Support Screw ......................................................... 1

39

350306162

* Washer (M6) ............................................................ 2

40

105018007

Bevel Scale ............................................................. 1

41

104056002

Lock Lever ............................................................... 1

42

101060002

"T" Handle Wrench .................................................. 1

43

101058102

Blade Changing Rod ............................................... 1

972000-704

Operator's Manual

* Standard Hardware Item – May Be Purchased Locally

Summary of Contents for SC155VS

























Reviews: