background image

3

 

 WARNING

'RQRWDWDQ\WLPHOHWEUDNHÀXLGVJDVROLQHSHWUROHXP

based products, penetrating oils, etc., come in contact 
with plastic parts. They contain chemicals that can 
damage, weaken or destroy plastic.

 

Ŷ

Electrical tools used on fiberglass material, wallboard, 

VSDFNOLQJ FRPSRXQGV RU SODVWHU DUH VXEMHFW WR

accelerated wear and possible premature failure 

because the fiberglass chips and grindings are highly 

abrasive to bearings, brushes, and commutators. We 

do not recommend using the product for extended 

periods of time on these types of materials.

 

 WARNING

Always wear safety goggles or safety glasses with side 
shields during power tool operation or when blowing 
dust. If operation is dusty, also wear a dust mask.

 

Ŷ

If the power supply cord is damaged, it must be replaced 

only by the manufacturer or by an authorised service 

centre to avoid risk. Contact authorised service centre.

 

Ŷ

For greater safety and reliability, all repairs should be 

performed by an authorised Ryobi service centre.

LUBRICATION

All of the bearings in the product are lubricated with a 

VXI¿FLHQWDPRXQWRIKLJKJUDGHOXEULFDQWIRUWKHOLIHVSDQRI

the product under normal operating conditions. Therefore, 

no further lubrication is required.

ENVIRONMENTAL PROTECTION

Recycle raw materials instead of disposing 
of as waste. The machine, accessories and 
packaging should be sorted for environment-
friendly recycling.

SYMBOLS ON THE PRODUCT

Safety alert

V

Volts

Hz

+HUW]

Alternating current

W

Watts

n

o

No-load speed

PLQʚï

Revolutions or reciprocations per minute

Class II tool, double insulation

+DPPHUPRGH

+DPPHUGULOOPRGH

Drill mode

Regulatory Compliance Mark (RCM). Product 
meets applicable regulatory requirements.

Please read the instructions carefully before 
starting the machine.

Waste electrical products should not be 
disposed of with household waste. Please 
recycle where facilities exist. Check with your 
local authority or retailer for recycling advice.

SYMBOLS IN THIS MANUAL

Connect to the power supply.

Disconnect from the power supply. 

Parts or accessories sold separately

Lock

Unlock

Off

On

Tile

Masonry

Wood

Metal

Note

The following signal words and meanings are intended to 

explain the levels of risk associated with this product:

 DANGER

Indicates an imminently hazardous situation, which, if not 

DYRLGHGZLOOUHVXOWLQGHDWKRUVHULRXVLQMXU\

 WARNING

Indicates a potentially hazardous situation, which, if not 

DYRLGHGFRXOGUHVXOWLQGHDWKRUVHULRXVLQMXU\

 CAUTION

Indicates a potentially hazardous situation, which, if not 

DYRLGHGPD\UHVXOWLQPLQRURUPRGHUDWHLQMXU\

CAUTION

(Without Safety Alert Symbol) Indicates a situation that 

may result in property damage.

Summary of Contents for RSDS1500





















Reviews: