12
English(original instructions)
EN
FR
DE
ES
IT
PT
NL
SV
DA
NO
FI
HU
CS
RU
RO
PL
SL
HR
ET
LT
LV
SK
BG
ASSEMBLY
■
Fit the lance into the gun and rotating it until the two
parts are completely locked. (Fig. 3)
■
Connect the gun to the high pressure hose. (Fig. 4)
■
Connect the high pressure hose to the water outlet
on the cleaner. (Fig.5)
■
Connect the water supply hose to the water inlet of
the cleaner (Fig.6). The supply hose must have an
internal diameter of at least 13mm (1/2 in.) and must
be reinforced.
WARNING:
The intake water temperature must not exceed
40°C (104° F). The water supply must not
exceed 7 bar (0.7Mpa)
CAUTION:
The cleaner must only be used with clean
water; use of unfiltered water or corrosive
chemicals will damage the cleaner.
■
Turn the motor switch to “OFF” position. (Fig.9)
■
Check that the electrical supply voltage and
frequency (Volt/Hz) correspond to those specified on
the cleaner rating plate. (Fig.7) If the power supply is
correct, you may now plug in the cleaner.
■
The cleaner must only be connected to power
sockets with regulation earth connection. A
differential safety breaker (30mA) will increase the
safety of operators.
OPERATION
■
Turn on the water supply tap fully.
■
Release the safety lock (Fig.8), then press the
trigger for a few seconds to allow air to escape
and to discharge residual pressure in the pipes.
■
Keeping the trigger pressed, push the switch to start
the motor. (Fig.9)
■
When re-starting the motor, always keep the
trigger pressed.
USE DETERGENT
■
Prepare the detergent according to the detergent
instructions. Fill the detergent tank.
■
Connect detergent tank to the gun and apply by
pressing trigger (Fig.10)
CORRECT USE OF STANDARD ACCESSORIES
■
The cleaner is equipped with the adjustable nozzle,
which provides some important functions:
■
LOW PRESSURE operation (for application of
detergent, and rinsing).
■
HIGH PRESSURE operation (for high pressure
washing).
■
Jet adjustment from pencil (high pressure) to fan (low
pressure). (Fig.11)
RECOMMENDED CLEANING PROCEDURE
■
Dissolve dirt by applying detergent with the fan jet
to the dry surface. On vertical surfaces, work from
the bottom upwards. Leave the detergent to act for
1 to 2 minutes, but do not allow to dry out. Apply the
high pressure jet, keeping the nozzle at least 30cm
(10 in.) from the surface, working from the bottom
upwards.
■
Avoid allowing the rinsing water to run on to
unwanted surfaces.
HOW TO DRAW WATER FROM A WATER TANK,
BUCKET, POND, etc
■
To draw water from a water tank, bucket, pond,
etc. you must first get a suction hose kit, which
is made up of a compatible hose and water filter.
Ryobi recommends the Expand-it™ Suction
Hose Kit.
■
Connect the suction hose to the water inlet on the
pressure cleaner and drop the other end into a water
tank, bucket, pond, etc. (Fig.15)
■
Ensure your water container is full of water (Fig.16)
■
Connect the power cord to an electricity source &
turn on at power point. Make sure the high pressure
nozzle is not connected & turn the unit on at the on/
off switch. Press the trigger on the gun-the unit is
ready for use once there is a constant water stream.
(Fig.17)
■
Connect the high pressure nozzle & press the hand
trigger to begin cleaning. (Fig.18)
MAINTENANCE
CAUTION:
Before working on the cleaner, disconnect the
plug from the power supply socket.
■
To ensure good performance, check and clean the
suction and detergent filters after every 50 hours of
operation. (Fig.12)
■
Clean the nozzle with the tool provided. Remove the
lance from the gun, (Fig.13), remove any dirt from
the nozzle hole (Fig.14) and rinse.
WARNING:
When servicing, use only identical replacement
parts. Use of any other parts may create a
hazard or cause product damage.
