background image

4

English (Original Instructions)

the string head.

 

Wear full eye and hearing protection while operating 

this product. If working in an area where there is a risk 

of falling objects, head protection must be worn.

 

Hearing protection may restrict the operator’s ability 

to hear warning sounds, pay particular attention to 

potential hazards around and inside the working area.

 

Wear heavy long trousers, non-slip protective footwear 

and gloves. Do not wear loose fitting clothing, short 

trousers, jewellery of any kind, or use with bare feet.

 

Secure long hair so it is above shoulder level to 

prevent entanglement in any moving parts.

 

Keep all bystanders, children, and pets at least 15 m 

away. Stop the product if anyone enters the area.

 

Do not operate this product when you are tired, ill, or 

under the influence of alcohol, drugs, or medication.

 

Do not operate in poor lighting. The operator needs 

clear unrestricted vision to identify potential hazards.

 

Keep firm footing and balance at all times. Do not 

overreach. Overreaching can result in loss of balance 

or exposure to hot surfaces.

 

Keep all parts of your body away from any moving part.

 

Do not touch area around the silencer or cylinder of the 

product, these parts get hot from operation.

 

Always stop the engine and allow it to cool before 

making any adjustments.

 

Do not smoke when mixing fuel or filling fuel tank.

 

Mix and store fuel in a container approved for fuel.

 

Mix fuel outdoors where there are no sparks or flames. 

Wipe up any fuel spillage. Move 9 m away from 

refueling site before starting engine.

 

Stop the engine and allow to cool before refueling or 

storing the product.

 

Allow the engine to cool; empty the fuel tank and 

secure the product from moving before transporting in 

a vehicle. 

 

Always stop the engine and make sure all moving 

parts have come to stop before:

 

servicing

 

leaving the product unattended

 

cleaning your product

 

changing accessories

 

clearing blockages

 

checking for any damage after hitting an object

4

Safety, performance, and dependability have been given 

top priority in the design of your grass trimmer.

INTENDED USE

This grass trimmer is intended to be used only by 

adults who have read and understood the instructions 

and warnings in this manual and can be considered 

responsible for their actions. This product is only intended 

for use outdoors in a well ventilated area. For safety 

reasons, the product must be adequately controlled by 

using two-handed operation.
The grass trimmer is designed for cutting grass, light 

weeds, and other similar vegetation at or about ground 

level. The cutting plane should be approximately parallel 

to the ground surface.
The grass trimmer should not be used to cut or trim 

hedges, bushes, or other vegetation where the cutting 

plane is not or about ground surface level.

 

WARNING

  To reduce the risk of injury, the user must read 

and understand the operator’s manual.

 

WARNING

  Do not attempt to operate the product until you 

have read thoroughly and understood completely 

all instructions and safety rules contained in this 

manual. Failure to comply may result in accidents 

involving  fire,  electric  shock,  or  serious  personal 

injury. Save the operator’s manual and review 

frequently for continuing safe operation, and 

instructing others who may use the product.

 

WARNING

  The product is not intended to be used by 

children or persons with reduced physical, mental, 

or sensory capabilities. Children should be 

adequately supervised to ensure they do not play 

with the product.

GENERAL SAFETY RULES

 

For safe operation, read and understand all instructions 

before using the product. Follow all safety instructions. 

Failure to follow all safety instructions listed below, can 

result in serious personal injury.

 

Some regions have regulations that restrict the use of 

the product. Check with your local authority for advice.

 

Do not allow children or untrained individuals to use 

the product.

 

Never start or run the engine in a closed or poorly 

ventilated area; breathing exhaust fumes can kill.

 

Clear the work area before each use. Remove all 

objects such as rocks, broken glass, nails, wire, or 

string, which can be thrown or become entangled in 

Summary of Contents for RLT254CSEON

















Reviews: