manualshive.com logo in svg

Ryobi RLT254CSEON, Original Instructions Manual, Page: 12 / 16

Share
Download
Ryobi RLT254CSEON Original Instructions Manual Download Page 12

12

English (Original Instructions)

 

■

Remove the spark arrestor using needle-nosed pliers. 

 

■

Clean the spark arrestor with a small wire brush. 

 

■

Replace the spark arrester. 

CLEANING THE AIR FILTER 

See Fig. 9

For proper performance and longer life, keep the air filter 

clean.

 

■

Ensure the product is in the off position.

 

■

Remove the air filter cover.

 

■

Remove the air filter and clean it with warm soapy water.

 

■

Rinse, and let the air filter dry completely.

 

■

Work two drops of lubricant into the air filter.

 

■

Replace the air filter (fits only one way).

 

■

Replace the air filter cover.

NOTE:

 The air filter should be replaced annually for the 

best performance.

FUEL CAP

 

WARNING

 A leaking fuel cap is a fire hazard and must be 

replaced immediately.

A  fuel  cap  contains  a  non-serviceable  filter  and  a 

check valve. A clogged fuel filter will cause poor engine 

performance. If performance improves when the fuel cap 

is loosened, check valve maybe faulty or filter clogged.

SPARK PLUG REPLACEMENT 

See Fig. 10

 

WARNING

 The material of the spark plug is metal. It becomes 

very hot after you stop the engine. Wait the engine 

to cool down before you disassemble the metal 

spark plug boot to avoid personal injury.

NOTE:

 The engine uses a Champion RCJ6Y spark plug 

or equivalent with 0.63 mm electrode gap. Use an exact 

replacement and replace the spark plug annually.
1.  Stop the engine.

2.  Hold the front portion of the rubber protect boot and 

pull it away from the housing.

3.  Pull the rubber protect boot upward to release the 

hook.

4.  Twist the metal spark plug boot and pull it away from 

the spark plug.

5.  Using a combination wrench, loosen the spark plug by 

turning it in a counterclockwise direction. Remove the 

old spark plug and replace with a new one. Tighten 

it in a clockwise direction using the combination 

wrench, recommended torque is 23.5 Nm. Assemble 

back the metal spark plug boot and the rubber protect 

boot.

ATTACHING THE HANGER CAP 

See Fig. 11

To use the hanger cap, push in the button and place the 

hanger cap over the lower end of the attachment. Slightly 

rotate the cap from side to side until the button locks into 

place.

NOTE:

 The secondary hole in the attachment shaft can be 

used for hanging purposes as well.

STORAGE (1 MONTH OR LONGER)

 

■

Drain all fuel from tank into a container approved for 

fuel. Run engine until it stops.

 

■

Clean all foreign material from the product. Store it in 

a well-ventilated place that is inaccessible to children. 

Keep away from corrosive agents such as garden 

chemicals and de-icing salts.

 

■

Abide by all ISO and local regulations for the safe 

storage and handling of fuel. Excess fuel should be 

used up in other 2-stroke engine powered equipment.

Summary of Contents for RLT254CSEON

















Reviews:

No comments