manualshive.com logo in svg

Ryobi RLT254CSEON, Original Instructions Manual, Page: 13 / 16

Share
Download
Ryobi RLT254CSEON Original Instructions Manual Download Page 13

13

English (Original Instructions)

TROUBLESHOOTING

IF THESE SOLUTIONS DO NOT SOLVE THE PROBLEM, CONTACT YOUR AUTHORISED SERVICE DEALER.

PROBLEM

POSSIBLE CAUSE

SOLUTION

Engine will not start.

1. No spark.

1. The spark plug may be damaged, remove it and check 

for dirt and cracks. Replace with a new spark plug.

2. No fuel.

2. Push primer bulb until bulb is full of fuel. If bulb does 

not fill, primary fuel delivery system is blocked. Contact 

a  servicing  dealer.  If  primer  bulb  fills,  engine  may  be 

flooded, proceed to next item.

3. Engine is flooded.

3. Remove spark plug, turn unit so spark plug hole is 

aimed at the ground. Rotate the choke dial to “

” 

position and pull starter cord 10 to 15 times. This will 

clear excess fuel from engine. Remove any fuel which 

splashed on the product. Clean and reinstall spark plug. 

Clean up any spilled fuel and move at least 9m away 

before restarting. Pull starter three times with choke dial 

at “

”. If engine does not start, rotate choke dial to 

“

” position and repeat normal starting procedure. If 

engine still fails to start, repeat procedure with a new 

spark plug.

4. Starter rope now harder to 

pull than when new.

4. Contact a servicing dealer.

5. Old fuel

5. Only use fresh fuel mixed with recommended oil. Fuel 

over 30 days old may prevent the unit from starting.

Engine starts but will not 

accelerate.

Engine requires approximately 

three minutes to warm up.

Allow engine to completely warm up. If engine does 

not accelerate after three minutes, contact a servicing 

dealer.

Engine starts but will only run at 

high speed at half choke.

Carburetor requires adjustment. Contact a servicing dealer.

Engine does not reach full 

speed and emits excessive 

smoke.

1. Check lubricant fuel mixture.

1. Use fresh fuel and the correct 2-stroke lubricant mix.

2. Air filter is dirty.

2. Clean air filter. Refer to 

Cleaning the Air Filter

 earlier 

in this manual.

3. Spark arrestor screen is dirty. 3. Contact a servicing dealer.

Summary of Contents for RLT254CSEON

















Reviews:

No comments