manualshive.com logo in svg

Ryobi RLT254CSEON, Original Instructions Manual, Page: 3 / 16

Share
Download
Ryobi RLT254CSEON Original Instructions Manual Download Page 3

3

English (Original Instructions)

Press the primer bulb 10 times.

Squeeze the throttle lock and throttle trigger to run.

Wait 10 seconds.

Pull: Quick release tab

Regulatory Compliance Mark (RCM). This product meets applicable regulatory requirements.

75  dB

Sound pressure level at idle

115 dB

Guaranteed sound power level

When fitting the line spool to the cutting means, this symbol should be visible to the operator.

Pull the starter grip.

To reduce the risk of injury or damage, avoid contact with any hot surface.

Starting a warm engine by electrical starter

Starting a cold engine by electrical starter

Starting a warm engine by hand

Starting a cold engine by hand

The following signal words and meanings are intended to explain the levels of risk associated with the product.

SYMBOLS

SIGNAL

MEANING

DANGER

Indicates an imminently hazardous situation, which, if not avoided, will 

result in death or serious injury.

WARNING

Indicates a potentially hazardous situation, which, if not avoided, could 

result in death or serious injury.

CAUTION

Indicates a potentially hazardous situation, which, if not avoided, may 

result in minor or moderate injury.

CAUTION

(Without Safety Alert Symbol) Indicates a situation that may result in 

property damage.

Summary of Contents for RLT254CSEON

















Reviews:

No comments