background image

English

7

 CAUTION

Keep extension cords away from the cutting area and 
position the cord so that it will not get caught on lumber, 
tools, etc., during cutting operation.

 WARNING

Check extension cords before each use, if damaged 
replace immediately. Never use tool with a damaged 
cord as touching the damaged area could cause 
electrical shock resulting in serious injury.

Extension cords suitable for use with your saw are 
available at your nearest service center.

 WARNING

Always wear safety goggles or safety glasses with side 
shields during power tool operation or when blowing 
dust. If operation is dusty, also wear a dust mask.

SYMBOL

Safety Alert

V

Volts

Hz

Hertz

Alternating Current

W

Watts

n

o

No load Speed

min-

1

Revolutions or reciprocations per minute

Maximum cutting capacity in wood

Conformity

Double Insulation

Wear ear protection

Wear eye protection

 

Please read the instructions carefully before 
starting the machine.

Waste electrical products should not be 
disposed of with household waste. Please 
recycle where facilities exist. Check with your 
Local Authority or retailer for recycling advice.

Summary of Contents for EJS700RG














Reviews: