background image

English

3

SPECIFICATIONS

Voltage

240 V   50 Hz

Input power

680 W

Stroke per minute

800 - 3000 min

-1

Stroke length

21 mm

Max cutting capacity

Wood

85 mm

Steel

8 mm

FEATURES

KNOW YOUR SAW

Before attempting to use your saw, familiarize yourself 
with all operating features and safety requirements.

ELECTRICAL CONNECTION

Your saw has a precision built electric motor. It should be 
connected only to a power supply of the type specifi ed by 
its rating plate. Do not operate this tool on direct current 
(DC). A substantial voltage drop will cause a loss of power 
and overheating. If your tool does not operate when 
plugged into an outlet, double-check the power supply.

 WARNING

Do not allow familiarity with tools to make you careless. 
Remember that a careless fraction of a second is 
suffi cient to infl ict severe injury.

OPERATION

SWITCH

See Figure 1.

 

To turn your saw ON, depress the switch.

 

Release trigger switch to turn your saw OFF.

LOCK-ON BUTTON

See Figure 1.

Your saw is equipped with a 

lock-on

 feature, which is 

convenient when continuous cutting for extended periods 
of time is required. To lock-on, depress the trigger switch, 
push in and hold the lock-on button located on the side of 
the handle, then release trigger switch. Release lock-on 
button and your saw will continue running.

To release the lock, depress the trigger switch and release.

If you have the lock-on feature engaged during use and 
your saw becomes disconnected from power supply, 

disengage the lock-on feature immediately.

 WARNING

Before connecting your saw to power supply source, 
always check to be sure it is not in lock-on position 
(depress and release trigger switch). Failure to do so 
could result in accidental starting of your saw resulting 
in possible serious injury. Also, do not lock the trigger on 
jobs where your saw may need to be stopped suddenly.

TRANSPARENT GUARD

See Figure 3.

For your protection, a transparent guard has been included 
with the saw. It is used to shield wood particles from the 
eyes. The transparent guard is attached by placing it in 
front of the blade area of the base and snapping it into the 
tabs on the sides of the saw base. For removal, simply 
pull the tap of the transparent guard. Make sure the saw is 
unplugged before installation and removal.

NOTE:

 The transparent guard can only be used for 

straight cutting.

TO INSTALL BLADES

See Figure 3 - 4.

 

Unplug the tool.

 WARNING

Failure to unplug your saw could result in accidental 
starting causing possible serious injury. 

 

Turn the tool  upside down.

 

Pull the tap of the transparent guard.

 

Rotate the quick release lever counter-clockwise and 
hold  in position.

 

Insert the saw blade into the groove in the roller guide,  
making sure the back of the saw blade is properly 
positioned in the  groove.

NOTE:

 Only T-shank saw blades can be used.

 

Push the saw blade into the blade clamp as far as it 
will  go.

 

Release the quick release lever.

 

Install the transparent guard.

Summary of Contents for EJS700RG














Reviews: