background image

11

English

 

„

Clamp the end of the air chuck down onto the presta 

valve adaptor by pressing air chuck clamp down until 

it locks into place.

 

„

After inflation, remove air chuck and tighten locking 

nut.

ACCESSORIES STORAGE
See figure 10.

When not in use, adaptors and needles provided with the 

inflator can be placed in the storage area located on the 

right side of the tool.

HOSE STORAGE
See figures 10 - 11

When not in use, the hoses provided with the inflator can 

be placed in the storage areas located on both sides of 

the inflator.

MAINTENANCE

 WARNING

When servicing, use only identical replacement parts. 

Use of any other parts may create a hazard or cause 

product damage.

 WARNING

Always wear safety goggles or safety glasses with side 

shields during power tool operation or when blowing 

dust. If operation is dusty, also wear a dust mask.

 WARNING

To avoid serious personal injury, always remove the 

battery pack from the tool when cleaning or performing 

any maintenance. 

Avoid using solvents when cleaning plastic parts. Most 

plastics are susceptible to damage from various types of 

commercial solvents and may be damaged by their use. 

Use clean cloths to remove dirt, dust, oil, grease, etc.

 WARNING

Do not at any time let brake fluids, gasoline, petroleum-

based products, penetrating oils, etc., come in contact 

with plastic parts. Chemicals can damage, weaken or 

destroy plastic which may result in serious personal 

injury.

ENVIRONMENTAL PROTECTION

Recycle raw materials instead of disposing 

of as waste. The machine, accessories 

and packaging should be sorted for 

environmental-friendly recycling.

SYMBOLS

Safety alert

Please read the instructions carefully 

before starting the machine.

Risk of injury. Explosive material.

Recycle

Waste electrical products should not be 

disposed of with household waste. Please 

recycle where facilities exist. Check 

with your Local Authority or retailer for 

recycling advice.

Summary of Contents for CIT1800G













Reviews: