INSTRUCTIONS FOR SAFE HANDLING
THANK YOU FOR BUYING A RYOBI PRODUCT.
To ensure your safety and satisfaction, carefully read through
this OWNER’S MANUAL and the SAFETY INSTRUCTIONS
before using the product.
1. Make sure that the tool is only connected to the voltage marked on
the name plate.
2. Never use the tool if its cover or any bolts are missing. If the cover
or bolts have been removed, replace them prior to use. Maintain all
parts in good working order.
3. Always secure tools when working in elevated positions.
4. Never touch the blade, drill bit, grinding wheel or other moving parts
during use.
5. Never start a tool when its rotating component is in contact with the
work piece.
6. Never lay a tool down before its moving parts have come to a
complete stop.
7.
ACCESSORIES
: The use of accessories or attachments other than
those recommended in this manual might present a hazard.
8.
REPLACEMENT PARTS
: When servicing use only identical
replacement parts.
CORDLESS IMPACT DRIVER SAFETY PRECAUTIONS
Be aware that since this tool does not have to be plugged into an
electrical outlet, it is always in operating condition.
First, charge the battery.
Be sure the battery is held correctly in place.
When not in use, lock the trigger, disconnect the tool.
When operating at high places, be aware of things below you.
Before driving a screw or a bolt into walls, ceilings or floors, ensure
that there are no concealed power cables inside.
Make sure that the bit is securely mounted. An incorrectly mounted
bit is extremely dangerous since it can fly off or break during operation.
Do not wear cloth gloves or a necktie since they could become
caught in a rotating bit.
DESCRIPTION
1. Bit holder
2. Bit
3. Trigger
4. Reversing switch
5. Battery
6. LED
DISPOSAL OF THE EXHAUSTED BATTERY
Recycle Ni-Cd batteries.
Take the battery to the shop from which it was purchased as
soon as the post-charging battery life becomes too short for
practical use.
Please do not discard the exhausted battery.
1.
2.
3.
4.
5.
6.
7.
8.
CHANGING THE ROTATION DIRECTION (Fig. 4)
To change the rotation direction, stop the tool and push the
reversing switch (4) to the opposite side.
When the reversing switch is pushed in from the side of “R”,
the bit rotates clockwise when viewed from the handle end of
the tool.
When the reversing switch is pushed in from the side of “L”,
the bit rotates counterclockwise.
The trigger can be locked by positioning the reversing switch
in the middle.
Lock the trigger whenever the tool is not in use.
Keep your workspace clean: Cluttered areas and benches invite injuries
Secure save working environment: Do not expose power tools to rain,.
Do not use power tools in damp or wet locations. Keep work area well
lit. Do not use power tools where there is risk to cause fire or explosion.
Keep children away: Do not let visitors touch the tool. All visitors should
be kept away from area.
Store idle tools: When not in use, tools should be stored in a dry, high
or locked up place, out of reach of children.
Do not force the tool: It will do the job better and safer at the rate for
which it was intended.
Use the right tool: Do not force small tools or attachments to do the job
of a heavy duty tool. Do not use tools for purposes not intended.
Wear protective glasses: Also use face or dust mask if the cutting
operation is dusty.
Do not overreach: Keep proper footing and balance at all times.
Maintain tool with care: Keep cutting tools sharp and clean for better
and safer performance. Keep handles dry, clean and free from oil and
grease.
Avoid unintentionally switch on: Do not carry a powered tool with a finger
on the switch. Ensure switch is off when plugging in.
Stay alert: Watch what you are doing. Use common sense. Do not
operate tool when you are tired.
9.
10.
11.
13.
14.
15.
16.
17.
18.
19.
12.
SPECIFICATIONS
Bit shank size
Driving capacity
Max. fastening torque
Voltage
Battery type
No load speed
Overall length
Net weight
Charging time
Charger rating
1/4” (6.35 mm)
M4 - M10 screws
M5 - M12 bolts
108 Nm
12 V
2,0 Ah
0 - 2300 min
-1
180 mm
1.7 kg
1 - 1.5 hour
240 V, 50 Hz, AC
APPLICATIONS
STANDARD ACCESSORIES
Charger, Battery, Driver bit,
(Also available with a spare battery.)
(Use only for the purposes listed below.)
1. Fastening / removing screws and bolts
NOISE BUILD-UP
Noise (sound pressure level) in the workplace can exceed 85
dB (A). In this case, sound insulation and hearing protection
measures must be taken by the operator.
MOUNTING AND REMOVING THE BIT (Figs. 1,2)
1. Slide the sleeve of the bit holder (1) forward.
2. Insert the bit (2) into the bit holder as far as it will go.
3. Release the sleeve.
4. Confirm that the bit is secured by pulling it forward.
(REMOVING)
(MOUNTING)
1. Slide the sleeve forward.
2. Pull the bit out.
NOTE!
The sizes of the bits which can be used for this tool are
A = 16 mm and B = 13 mm. (Fig. 2)
CAUTION!
Use a bit that matches the screw or bolt to be driven.
CAUTION!
Do not use a damaged bit.
SWITCH (Fig. 3)
This tool is started and stopped by squeezing and releasing
the trigger (3).
The rotation speed is variable from 0 through 2300 min
-1
by
controlling the trigger-squeezing force.
Page 2
