3 – English
GENERAL SAFETY RULES
WARNING:
Read and understand all instructions.
Failure to follow
all instructions listed below, may result in electric shock,
fire and/or serious personal injury.
READ ALL INSTRUCTIONS
KNOW YOUR POWER TOOL.
Read the operator’s
manual carefully. Learn the grinder’s applications and
limitations as well as the specific potential hazards related
to this tool.
GUARD AGAINST ELECTRICAL SHOCK BY
PREVENTING BODY CONTACT WITH GROUNDED
SURFACES.
For example, pipes, radiators, ranges,
refrigerator, enclosures.
KEEP GUARDS IN PLACE
and in good working order.
REMOVE ADJUSTING KEYS AND WRENCHES.
Form
the habit of checking to see that keys and adjusting
wrenches are removed from tool before turning it on.
KEEP WORK AREA CLEAN.
Cluttered areas and benches
invite accidents.
DO NOT
leave tools or pieces of wood
on the bench grinder while it is in operation.
DO NOT USE IN DANGEROUS ENVIRONMENTS.
Do
not use power tools in damp or wet locations or expose
to rain. Keep the work area well lit.
KEEP CHILDREN AND VISITORS AWAY.
All
visitors should wear safety glasses and be kept a safe
distance from work area. Do not let visitors contact
tool or extension cord while operating.
MAKE WORKSHOP CHILDPROOF
with padlocks and
master switches, or by removing starter keys.
DON’T FORCE TOOL.
It will do the job better and safer
at the feed rate for which it was designed.
USE RIGHT TOOL.
Don't force the tool or attachment to
do a job it was not designed for. Don't use it for a purpose
not intended.
USE THE PROPER EXTENSION CORD.
Make sure
your extension cord is in good condition. Use only a
cord heavy enough to carry the current your product will
draw. An undersized cord will cause a drop in line volt-
age resulting in loss of power and overheating. A wire
gauge size (A.W.G.) of at least
16
is recommended for an
extension cord 25 feet or less in length. If in doubt, use
the next heavier gauge. The smaller the gauge number,
the heavier the cord.
DRESS PROPERLY.
Do not wear loose clothing, gloves,
neckties, or jewelry. They can get caught and draw you
into moving parts. Rubber gloves and nonskid footwear
are recommended when working outdoors. Also wear
protective hair covering to contain long hair.
ALWAYS WEAR SAFETY GLASSES WITH SIDE
SHIELDS.
Everyday eyeglasses have only impact-
resistant lenses, they are not safety glasses.
SECURE WORK.
Use clamps or a vise to hold work
when practical. It’s safer than using your hand and frees
both hands to operate tool.
DON’T OVERREACH.
Keep proper footing and
balance at all times.
MAINTAIN TOOLS WITH CARE.
Keep tools sharp
and clean for better and safer performance. Follow instruc-
tions for lubricating and changing accessories.
DISCONNECT TOOLS.
When not in use, before
servicing, or when changing attachments, grinding
wheels, etc., all tools should be disconnected.
AVOID ACCIDENTAL STARTING.
Be sure switch is off
when plugging in any tool.
USE RECOMMENDED ACCESSORIES.
Consult the
operator’s manual for recommended accessories. The
use of improper accessories may cause risk of injury to
persons.
NEVER STAND ON TOOL.
Serious injury could occur if
the tool is tipped or if the cutting tool is unintentionally
contacted.
CHECK DAMAGED PARTS.
Before further use of the
tool, a guard or other part that is damaged should be
carefully checked to determine that it will operate properly
and perform its intended function. Check for alignment
of moving parts, binding of moving parts, breakage of
parts, mounting and any other conditions that may affect
its operation. A guard or other part that is damaged must
be properly repaired or replaced by an authorized service
center to avoid risk of personal injury.
PROTECT YOUR LUNGS.
Wear a face or dust mask if
the grinding operation is dusty.
PROTECT YOUR HEARING.
Wear hearing protection
during extended periods of operation.
DO NOT ABUSE CORD.
Never yank cord to discon-
nect from receptacle. Keep cord from heat, oil, and sharp
edges.
USE OUTDOOR EXTENSION CORDS.
When tool
is used outdoors, use only extension cords with
approved ground connection that are intended for use
outdoors and so marked.
WHEELS COASTS AFTER BEING TURNED OFF.
NEVER USE IN AN EXPLOSIVE ATMOSPHERE.
Normal sparking of the motor could ignite fumes.
