background image

ALL IMPLIED WARRANTIES ARE LIMITED IN 
DURATION TO THE TWO (2) YEAR WARRANTY 
PERIOD OR NINETY (90) DAYS FOR PRODUCTS
USED FOR ANY COMMERCIAL PURPOSE. 
ACCORDINGLY, ANY SUCH IMPLIED WARRANTIES
INCLUDING MERCHANTABILITY, FITNESS FOR A
PARTICULAR PURPOSE, OR OTHERWISE, ARE 
DISCLAIMED IN THEIR ENTIRETY AFTER THE 
EXPIRATION OF THE APPROPRIATE TWO-YEAR 
OR NINETY DAY WARRANTY PERIOD. RYOBI’S
OBLIGATION UNDER THIS WARRANTY, IS STRICTLY
AND EXCLUSIVELY LIMITED TO THE REPAIR OR
REPLACEMENT OF DEFECTIVE PARTS, AND ROP
DOES NOT ASSUME OR AUTHORIZE ANYONE TO
ASSUME FOR THEM ANY OTHER OBLIGATION.
SOME STATES DO NOT ALLOW LIMITATIONS ON
HOW LONG AN IMPLIED WARRANTY LASTS, SO
THE ABOVE LIMITATION MAY NOT APPLY TO YOU.

RYOBI ASSUMES NO RESPONSIBILITY FOR 
INCIDENTAL, CONSEQUENTIAL OR OTHER 
DAMAGES INCLUDING, BUT NOT LIMITED TO
EXPENSE OF RETURNING THE RYOBI PRODUCT 
TO AN AUTHORIZED SERVICE DEALER AND
EXPENSE OF DELIVERING IT BACK TO THE 
OWNER, MECHANIC’S TRAVEL TIME, TELEPHONE
OR TELEGRAM CHARGES, RENTAL OF A LIKE
PRODUCT DURING THE TIME WARRANTY SERVICE
IS BEING PERFORMED, TRAVEL, LOSS OR DAMAGE
TO PERSONAL PROPERTY, LOSS OF REVENUE,
LOSS OF USE OF THE PRODUCT, LOSS OF TIME,
OR INCONVENIENCE. SOME STATES DO NOT
ALLOW THE EXCLUSION OR LIMITATION OF 
INCIDENTAL OR CONSEQUENTIAL DAMAGES, SO
THE ABOVE LIMITATION OR EXCLUSION MAY NOT
APPLY TO YOU.

This warranty gives you specific legal rights, and you
may also have other rights which vary from state to
state.

This warranty applies to all RYOBI Products
manufactured by RYOBI and sold in the United States
and Canada.

To locate your nearest service dealer dial
1-800-345-8746 in the United States or
1-800-265-6778 in Canada.

RYOBI OUTDOOR PRODUCTS

550 N. 54th Street

Chandler, AZ 85226 U.S.A.

RYOBI CANADA INC.

275 Industrial Rd

Cambridge, Ontario N1R 6K2 CANADA

RYOBI OUTDOOR PRODUCTS warrants each new
RYOBI Product for two (2) years according to the 
following terms.

This warranty extends to the original retail purchaser
only and commences on the date of original retail 
purchase.

Any part of the RYOBI Product manufactured or 
supplied by RYOBI and found in the reasonable 
judgement of RYOBI to be defective in material or
workmanship will be repaired or replaced by an 
authorized RYOBI service dealer without charge for
parts and labor.

The RYOBI Product including any defective part must
be returned to an authorized service dealer within the
warranty period. The expense of delivering the RYOBI
Product to the dealer for warranty work and the
expense of returning it back to the owner after repair
or replacement will be paid for by the owner. RYOBI’s
responsibility in respect to claims is limited to making
the required repairs or replacements and no claim of
breach of warranty shall be cause for cancellation or
rescission of the contract of sale of any RYOBI
Product. Proof of purchase will be required by the
dealer to substantiate any warranty claim. All warranty
work must be performed by an authorized RYOBI 
service dealer.

This warranty is limited to ninety (90) days from the
date of original retail purchase for any RYOBI Product
that is used for rental or commercial purposes, or any
other income-producing purpose.

This warranty does not cover any RYOBI Product that
has been subject to misuse, neglect, negligence, or
accident, or that has been operated in any way 
contrary to the operating instructions as specified in
the RYOBI Operator’s Manual. This warranty does not
apply to any damage to the RYOBI Product that is the
result of improper maintenance or to any RYOBI
Product that has been altered or modified so as to
adversely affect the product's operation, performance
or durability or that has been altered or modified so as
to change its intended use. The warranty does not
extend to repairs made necessary by normal wear or
by the use of parts or accessories which are either
incompatible with the RYOBI Product or adversely
affect its operation, performance or durability.

In addition, this warranty does not cover:

A. Tune-ups - Spark Plugs, Carburetor Adjustments,

Filters

B. Wear items - Bump Knobs, Outer Spools,

Cutting Line, Inner Reels, Starter Pulley,
Starter Ropes, Drive Belts

RYOBI reserves the right to change or improve the
design of any RYOBI Product without assuming 
any obligation to modify any product previously 
manufactured.

SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE.

FOR QUESTIONS CALL 1-800-345-8746 IN U.S.

OR 1-800-265-6778 IN CANADA

OPERATOR’S MANUAL PART NO. 182394

REV. A (9554)

PRINTED IN U.S.A.

5/99

LIMITED TWO-YEAR WARRANTY

Summary of Contents for 875r































Reviews: