background image

OIL AND FUEL INFORMATION

11

FUELING UNIT

WARNING:

Gasoline is extremely flammable

and its vapors can explode if ignited. To
avoid serious personal injury, always stop the
engine and allow it to cool before filling the
fuel tank. Do not smoke while filling the tank.
Keep sparks and open flames away from the
area.

1. Remove fuel cap (Fig. 7).

WARNING:

Remove fuel cap slowly to avoid

injury from gasoline spray. 

Fig. 7

Fuel Cap

Fuel Tank

Gas Can Spout

2. Place spout of gas container into the fill hole on the

fuel tank (Fig. 7) and fill tank.

WARNING: 

Add gasoline in a clean, well 

ventilated area outdoors. Avoid creating a
source of ignition for spilt fuel.

NOTE:

Do not overfill tank. 

3. Wipe up any gasoline that may have spilled 

4. Reinstall the fuel cap.

WARNING:

Never operate the unit without

the fuel cap securely in place.

5. Move the unit at least 30 ft. (9.1 m) from the fueling

source and site before starting the engine. 

NOTE:

Dispose of the old gasoline in accordance to
Federal, State, and Local regulations.

RECOMMENDED FUEL TYPE

Old fuel is the primary reason for the unit not
running properly. Be sure to use fresh, clean,
unleaded Gasoline.

NOTE:

This is a four cycle engine. In order to avoid
damage to the unit,

do not mix oil with

Gasoline

.

Definition of Blended Fuels

Today's fuels are often a blend of gasoline and 
oxygenates such as ethanol, methanol or MTBE (ether).
Alcohol-blended fuel absorbs water. As little as 1%
water in the fuel can make fuel and oil separate or form
acids when stored. Use fresh fuel (less than 60 days
old), when using alcohol-blended fuel.

Using Blended Fuels

If you choose to use a blended fuel, or its use is
unavoidable, follow recommended precautions.

Always use fresh unleaded gasoline 

Use the fuel additive STA-BIL

®

or an equivalent.

Drain tank and run the engine dry before storing unit.

Using Fuel Additives

The use of fuel additives, such as STA-BIL

®

Gas

Stabilizer or an equivalent, will inhibit corrosion and 
minimize the formation of gum deposits. Using a fuel
additive can keep fuel from forming harmful deposits in
the carburetor for up to six (6) months. Add 0.8 oz. 
(23 ml.) of fuel additive per gallon of fuel according to the
instructions on the container. NEVER add fuel additives
directly to the unit's gas tank. 

Unleaded

Gasoline

Summary of Contents for 875r































Reviews: