background image

The detector must be turned off before exchanging the search coil or batteries.

The device must not be stored with depleted regular or rechargeable batteries installed.   
When the device is to be stored for more then a month, the cells must be removed 
regardless of their change status. 

The detector must not be subjected to high temperatures – leaving the detector on a hot  
day in a car may damage it. 

Do not store the detector in an unheated room during the winter. The best place to 
store the detector is in a dry room, at room temperature. 

The search coil is waterproof to a depth of 1m, the detector electronics are not 
waterproof. 

 

Cleaning the detector must be done using only water with soap on a damp sponge. 

Do not use any solvents or petroleum products

. Regularly clean the stems and 

cam locks. 

If you use wired headphones – remove the plug from the headphone socket at the end 
of each search as transporting a detector with the plug plugged in increases the risk of 
damaging the socket. 

In difficult weather conditions it is advised to use a cover for the control panel and the 
battery compartment. 

Correct maintenance of the detector will increase its reliability and longevity.

ULTRA DEEP PROGRAM

DEEP PROGRAM

BIG SILVER PROGRAM

Page

Setting

Factory value

Page

Setting

Factory value

Page

Setting

Factory value

Engine

Frequency

5000 Hz Engine

Frequency

7000 Hz Engine

Frequency

5000 Hz

Engine

Hot rock

+10 Engine

Hot rock

+5 Engine

Hot rock

+10

Engine

Reaction

1 Engine

Reaction

2 Engine

Reaction

3

Engine

Masking

6 Engine

Masking

4 Engine

Masking

3

Audio

Th Level

30 Audio

Th Level

5 Audio

Th Level

10

Audio

Th Tone

100 Hz Audio

Th Tone

150 Hz Audio

Th Tone

250 Hz

Audio

Th Sens

30 Audio

Th Sens

30 Audio

Th Sens

25

Audio

VCO

Yes Audio

VCO

Yes Audio

VCO

Yes

Audio

Th SAT

5 Audio

Th SAT

5 Audio

Th SAT

10

Audio

Audio Gain

0 Audio

Audio Gain

20 Audio

Audio Gain

20

Audio

Iron volume

0 Audio

Iron volume

0 Audio

Iron volume

0

Audio

Tones

Relics 3 Audio

Tones

Relics 3 Audio

Tones

Coin 3

Screen

ID Type

6 kHz Screen

ID Type

6 kHz Screen

ID Type

6 kHz

Screen

Hold Time

5 s Screen

Hold Time

5 s Screen

Hold Time

5 s

Screen

ID Gain

Normal Screen

ID Gain

Normal Screen

ID Gain

Normal

RUTUS

 

Alter71

 ver. 2.0

                                                                                                      

 23 

Summary of Contents for Alter71




























Reviews: