background image

For Customer Services & Spare Parts please call

0345 208 8750

or visit us at 

https://mda.russellhobbs.com

25

WARNING-

THIS APPLIANCE MUST BE EARTHED

This appliance is designed to operate from a mains supply of AC220 - 240V ~ 50HZ.
Check that the voltage marked on the product corresponds with your supply voltage.

For UK use only

Plug fitting details for rewireable plugs only (where applicable):

As the colours of the wires in the mains lead of this appliance may not correspond
with the coloured markings identifying the terminals in your plug, proceed as follows:

The GREEN/YELLOW wire is the EARTH and must be connected to the terminal which
is marked with the letter E or by the earth symbol or coloured GREEN or
GREEN/YELLOW.

The BLUE wire is the NEUTRAL and must be connected to
the terminal marked with the letter N or coloured BLACK.

The BROWN wire is the LIVE wire and must be connected
to the terminal marked with the letter L or coloured RED.

Always ensure that the plug cord grip is fastened correctly.

If a 13A (BS1363) fused plug is used it must be fitted with a 13amp fuse conforming
to BS1362 and be BSI or ASTA approved.

Connection to the mains supply

Summary of Contents for RH60GH401





























Reviews: