background image

V1.1 

Rungu Rear Rack owner’s manual –

 Use with non-electric and mid-drive electric Rungu 

Copyright 2017 Standard Bearer Machines, LLC 

 

Page 

1

 of 

18

 

rungu

®

 rear rack owner 

manual - use with non-
electric rungu and mid-
drive versions  

Congratulations on purchasing the Rungu Rear Rack for your Rungu Trike

1

!  This document reviews the 

installation and capabilities of the rear rack. Before you ride with your Rear Rack, 

please read the 

following instructions carefully

.   

 

 

IMPORTANT- Standard Bearer Machines will not be liable for any damage or injury that may occur due 
to the use of our products. By using the Rear Rack, you are agreeing to Standard Bearer Machines, LLC 
Terms and Conditions and the warnings and conditions included in this document. 

 

                                                           

1

 

As the owner, you agree and are bound by all sales and transfer conditions as defined in “

SBM Rungu Sales Terms 

and Conditions US 2017a” or “S

BM Rungu Sales Terms and Conditions US 2017 

 

Demo Model.” Copies of these 

documents are available on the USB drive that ships with the product or upon request by e-mailing 

[email protected]

. 

 

Summary of Contents for Rear Rack



















Reviews: