background image

Tumbler MPR 300 

 

Table of contents 

Safety instructions ............................................................................. 3 

1.1 

Safety instructions ................................................................... 3 

1.2 

Remaining risk of accidents .................................................. 6 

1.3 

Intended use ............................................................................... 7 

Installation instructions ................................................................... 8 

2.1 

Machine transport and setup ............................................... 8 

2.2 

Workplace description ............................................................. 9 

2.3 

Connecting the machine .......................................................10 

Operating instructions ....................................................................11 

Cleaning instructions .......................................................................13 

4.1 

Safety instructions .................................................................13 

4.2 

Cleaning agents and disinfectants....................................14 

4.3 

Cleaning procedure .................................................................14 

Service: care, maintenance, repair .............................................16 

5.1 

Regular care ..............................................................................17 

5.2 

Regular maintenance .............................................................18 

5.3 

Repairs and spare parts ........................................................18 

Disposal ................................................................................................18 

Technical documentation ..............................................................19 

7.1 

Technical data ..........................................................................19 

7.2 

Electrical circuit diagram ......................................................20 

EC Declaration of Conformity according to Directive 

2006/42/EC .................................................................................................21 
 

 
 
 
Status: 16.03.2022

 (Version 2.1)

 

Subject to change 

 

 

Summary of Contents for MPR 300






















Reviews: