background image

INTRODUCTION

ВВЕДЕНИЕ

This manual has been prepared for 
workshop personnel expert in the use of 
the lift (operator) and technicians 
responsible for routine maintenance 
(maintenance fitter); read the manual 

Настоящее руководство предназначено для 
персонала имеющего навыки работы с 
подъёмником (операторы) и обслуживающих 
специалистов (сервисные инженеры); 
прочитайте руководство до выполнения любых 
операций с подъёмником в т.ч. распаковки. 
Руководство содержит важные сведения 
относящиеся к:

before carrying out any operation with the lift and/or 
the packing. This manual contains important 
information regarding:

- The personal safety of operators and maintenance 
workers

- Личной безопасности операторов и сервисных 
инженеров

- Lift safety

- Безопасности подъёмных операций

- The safety of lifted vehicles

- Безопасности поднимаемых автомобилей

Conserving the manual

Хранение руководства

This manual is an integral part of the lift, which 
it should always accompany, even if the unit is 
sold. 
The manual must be kept in the vicinity of the 
lift, in an easily accessible place.

Настоящее руководство является элементом 
комплекта поставки подъёмника, даже в случае 
повторной продажи изделия.
Руководство должно храниться вблизи подъёмника, 
в легкодоступном месте.

The operator and maintenance staff must be able to locate 
and consult the manual quickly and at any time. Attentive 
and repeated reading of chapter 3, which contains 
important information and safety warning, is particularly 
recommended.

Оператор и/или сервисный инженер должны иметь 
удобный доступ к руководству в любое время. 
Настоятельно рекомендуется уделить повышенное 
внимание Разделу 3, содержащему важную 
информацию о требованиях безопасности.

The lifting, transport, unpacking, assembly, 
installation, starting up, initial adjustment 
and testing, extraordinary maintenance, 
repair, overhauls, transport and 

Все погрузочно-разгрузочные и 
транспортировочные работы, распаковка, 
установка, ввод в эксплуатацию, настройка и 
испытания подъёмника должны выполняться 
персоналом прошедшим специальную 
подготовку у авторизованного дилера либо 
производителя.

dismantling of the lift must be performed by 
specialized personnel from the licensed dealer or an 
service center authorized by the manufacturer.

The manufacturer declines all responsibility for injury to 
persons or damage to vehicles or objects when any of the 
above mentioned operations has been performed by 
unauthorized personnel or when the rack has been 
subject to improper use.

Производитель не несёт ответственности за 
повреждения причинённые персоналу, автомобилю, 
иным лицам или объектам, при выполнении 
вышеуказанных операций неуполномоченным 
персоналом.

This manual indicates only the operative 
and safety aspects that may prove useful to 
the operator and maintenance worker, for 

Данное руководство содержит именно те 
аспекты по безопасности и эксплуатации, 
которые необходимы оператору и/или 
сервисному инженеру для изучения конструкции 
подъёмника, а также правил его эксплуатации.

better understanding the structure and operation of 
the lift and for best use of the same.

In order to understand the terminology used in this manual, 
the maintenance and repair activities, the ability to interpret 
correctly the drawings and descriptions contained in the 
manual and be the country in which the machine has been 
installed.
The same applies to the maintenance fitter, who must also 
possess specific and specialized knowledge (mechanical, 
engineering) needed to perform the operations described in 
the manual in complete safety. The words “operator” and 
“maintenance fitter” used in this manual are construed as 
follows:

Применение данного руководства для выполнения 
обслуживания и ремонта подъёмника, требует от 
сервисного инженера знания технических терминов, 
умения читать чертежи и схемы.
Тоже самое относится к сервисному инженеру, 
который также должен обладать специальными 
знаниями (в области механики, гидравлики, 
электромонтажа и т.д.), для того чтобы 
осуществлять все операции в безопасном режиме. 
Термины «оператор» и «сервисный инженер», 
применяемые в руководстве, истолковываются:

- OPERATOR: person authorized to use the lift
- MAINTENANCE FITTER: person authorized for routine 
maintenance of the lift.

- ОПЕРАТОР: мастер допущенный к эксплуатации 
подъёмника; 
- СЕРВИСНЫЙ ИНЖЕНЕР: мастер допущенный к 
обслуживанию и ремонту подъёмника 

NOTE: Manufacturer own the right to make 
little change for the manual

Внимание: Производитель имеет право на 
внесение изменений в настоящее руководство 
без дополнительных предупреждений

5

Summary of Contents for RLS-G 3.5T






































Reviews: