Ruckus Wireless T811-CM Installation Manual Download Page 32

Page: 32 / 54

T811-CM AP Installation Guide, 800-71436-001 Rev A

Installing the T811-CM

Deploying the T811-CM

Figure 11. Connection Status page - Page 2 of 2

Continue with

Configuring the Downstream Frequency

The

Configure Status

page allows you to set the downstream frequency for the cable modem.

Configuring the downstream frequency enables the device to quickly obtain a direct frequency lock
with the CMTS upon bootup and helps to save several minutes of scanning for an available
downstream frequency from the CMTS.

Log into the

Status

page as described in

Logging Into the CM Web Interface

Click

Configure

in the left sidebar. The CM Web interface displays the

Configure Status

page.

See

Figure 12

Figure 12. Configure Status page

In the

Configure DS Frequency

text box, enter the downstream frequency (in Hertz) that you want

the cable modem to use to connect to the CMTS when it boots up.

Click

Set Values and Reboot

to have the cable modem save your changes and reboot.

Continue with

Administering Cable Modem Passwords

The parameters on the

Security Status

page allow you to change the CM login and password, and/

or restore the factory defaults.

Log into to the

Status

page as described in

Logging Into the CM Web Interface

Click

Security

in the left sidebar. The CM Web interface displays the

Security Status

page.

Summary of Contents for T811-CM






















































Search results

Summary of Contents for T811-CM

Reviews:

Brands by name

Popular brands

Ruckus Wireless T811-CM, Installation Manual

Search results

Summary of Contents for T811-CM

Reviews:

Brands by name

Popular brands