manualshive.com logo in svg

RTS KP-12, User Instructions, Page: 83 / 106

Share
Download
RTS KP-12 User Instructions Download Page 83

17

Addresses and the RVON-1

11.

Gently secure the board in place 

NOTE

: Be sure the orientation of the board is correct, otherwise undesirable effects may occur. Make sure the RJ-45 

connection is positioned so it will fit through the specified knockout on the back cover. When installing the RVON-1 card in an 
existing KP-32 or KP-812, each keypanel needs to be upgraded to include the following:

KP-32

•

A backplate that allows for the RJ-45 connection (Ethernet).

•

Larger flash chips.

KP-812

•

A backplate that allows for the RJ-45 connection (Ethernet)

•

Extension for the RJ-45 connector.

RVON-1 Relay

When connected to an Ethernet LAN, audio comes from the RVON-1 card; and, when Ethernet is not plugged in, the audio 
comes from the AIO connection. Note, the user does not need to remove the RVON-1 to switch to AIO mode.

WARNING

: You cannot have both an Ethernet connection and an AIO connection simultaneously. If the Ethernet and AIO 

are connected simultaneously, no audio communication will occur.

Addresses and the RVON-1

Because the RVON-1 has an Ethernet interface, it is required to have a MAC (Media Access Control) Address. This is a low 
level address that contains 48 bits. Do NOT confuse this address with an IP (Internet Protocol) Address. In order to be IP com-
pliant, all cards must have a unique MAC ID when shipped from the manufacturer. Typically, the MAC ID of a piece of hard-
ware, such as the RVON-1 card, has a fixed or static address. Where as the RVON-1 card’s IP Address can change over time.

The MAC Address uniquely identifies each node of a network and interfaces directly with the network media. The RVON-1 
card has a small 8-pin serial device on the board that the processor can read the unique MAC Address from. For more 
information on MAC IDs, contact technical support.

NOTE

: Each RVON-1 card needs to be programmed with its own IP Address.

Figure 5. 

The J37 connector on the KP-812 board.

Summary of Contents for KP-12











































































































Reviews:

No comments