background image

 

2

 

FOREWORD 

 
Congratulations with the purchase of your Genesis. To ensure long and safe use of this Genesis, it 
is of major importance to all users to read and understand this user manual.

 

Operation of this machine is not safe without full knowledge of the content of the manual. 
 
The Genesis is not an independently operating machine. The user is responsible for using the 
appropriate tractor. The user must also check the tractor/Genesis combination for safety aspects, 
such as noise level, adequate user instructions and any risks.

 

 
The Genesis is solely intended for use on food plot areas. 
 
On the next page you will first find the general safety instructions. Every user must know and apply 
them. After this, a registration card is included. This card should be returned for handling any future 
claims.

 

 
This user manual offers many numbered instructions An 

 

symbol indicates a safety instruction. 

A           symbol indicates a tip and/or note. 
 
At the time of publishing all information and technical specifications provided are the most recent. 
Design specifications to the design of the machine may be changed without prior notice to the 
owner of the Genesis. 
 

GUARANTEE CONDITIONS 

 

THIS GENESIS COMES WITH A GUARANTEE FOR DEFECTIVE MATERIALS. THIS GUARANTEE IS 
VALID FOR A PERIOD OF 12 MONTHS FROM THE PURCHASING DATE. GENESIS GUARANTEES 
ARE SUBJECT TO THE “GENERAL CONDITIONS FOR SUPPLY OF PLANT AND MACHINERY FOR 
EXPORT, NUMBER 188”, PUBLISHED UNDER THE AUSPICES OF THE UNITED NATIONS 
ECONOMIC COMMISSION FOR EUROPE. 

 

REGISTRATION CARD 

 
For your own information, please complete the table below: 

 
 
Serial number of machine

 

 

 
Dealer name

 

 

 
Purchasing date

 

 

 
Remarks 

 

 

Summary of Contents for Genesis 10


























Reviews: