background image

 

11

 

3.0  CONNECTING TO THE TRACTOR 

 

Checks prior to connecting the Genesis: 

 

 

Check the Genesis for any visual damage, and repair if safe operation of the 
machine cannot be guaranteed.

 

 

Check whether all nuts and bolts have been tightened properly.

 

  Check whether all protective covers and safety stickers are in place on the machine, 

and whether they are undamaged. 

NEVER

 use the machine without them. 

 
The Genesis can be connected to the tractor using the 3-point hitch. The method is as follows: 
(

Figure 7

)

 

 

1.  Remove the 3-point pins (1 and 2). 
2.  Carefully back up the tractor, so that the lifting arms (4) can be connected to the 

frame. 

 

!! Make sure the tractor is secured in place and cannot start moving!! 
!! Stop the engine of the tractor before getting off!! 

 
3.  Connect the lifting arms to the bottom 3-point pins (2) and secure them using the 

included locking pins. 

4.  Set the stabilizer of the tractor to a 100 mm sideways stroke. 
5.  Mount the top link (3) of your tractor and extend it until it is at the same height as the 

top 3-point hitch (1) of the Genesis. 

6.  Connect the top link (3) to the frame using the top pin (1) and secure using the 

included locking pin. 

7.  Keep extending/retracting the top link until the machine makes a 90° angle with the 

ground. 

 

!! Make sure all locking pins are secured!! 

 
8.  Start the tractor and lift the Genesis off the ground.  
9.  Slide the support legs (5) up in the working position. 

 

 

Figure 7

 

Summary of Contents for Genesis 10


























Reviews: