background image

 

15

V  A C U U M    P U M P    O  I  L    L  I  F E

R E M A I N I N G   # #  H O U R S

                                   
                      C O N  T  I  N U E ?

 

 

VACUUM PUMP MAINTENANCE 

Oil must be periodically changed in the vacuum pump 
to ensure continued performance. The RHS980 will 
display a reminder after every ten  hours of vacuum 
pump use. 

A drain port and fill port for the vacuum pump protrude 
through the rear wall of the RHS980 – to the left of the 
handle. A sight glass for viewing the oil level in the 
vacuum pump is located on the end of the fill port. 

Drain oil from the drain port and refill with new oil 
through the fill port. Use oil which is specially 
formulated for a vacuum pump. 

RTI Part Numbers: 

011-80004-00  One quart bottle 

360-80012-00  Case of 12 one quart bottles 

The oil level should be visible approximately  one-half 
the way up in the sight glass. 

 

COMBO FILTER MAINTENANCE 

The RHS980 combo filter must be replaced after every 
150 lbs. of refrigerant has been recovered from A/C 
systems. An alert will display when the filter life is at 
100 lbs. The RHS980 will shut down when the filter life 
is at 150 lbs. A new filter must be installed and a serial 
number entered to re-start the RHS980. 

A special routine for changing the combo filter is 
explained on Page 12. 

The document pocket on the left side of the RHS980 
can be removed to gain access to the combo filter. 
The combo filter is on the right side of the manifold as 
shown in the photo. A hex on top of the filter is 
provided to make filter removal and installation easy. 
Use an end wrench on this hex. New O-rings are 
provided with the replacement filter. 

A serial number is printed on a label attached to the 
new filter. Make a note of this number as it may not be 
visible when the filter is installed. This serial number 
must be entered to reset the 150 hour filter life routine. 

 

Order Filter Kit: 360-82133-00 

 

The RHS980 records the hours the vacuum pump 
runs. A reminder screen displays when that total 
equals 10 hours. The vacuum pump oil should be 
changed at that time. This screen displays the hours 
remaining until the reminder screen will display. Press 

START

 key to continue. 

Summary of Contents for RHS 980



















Reviews: