background image

3

It’s Under Control

®

3

It’s Under Control

®

This equipment has been tested and found to comply with the limits for a Class 

B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed 

to provide reasonable protection against harmful interference in a residential 

installation. Any changes or modifications not expressly approved by the party 

responsible for compliance could void the user’s authority to operate the device.
This equipment generates, uses, and can radiate radio frequency energy and, if 

not installed and used in accordance with the instructions, may cause harmful 

interference to radio communications. However, there is no guarantee that 

interference will not occur in a particular installation. 
If this equipment does cause harmful interference to radio or television 

reception, which can be determined by turning the equipment off and on, the 

user is encouraged to try to correct the interference by one or more of the 

following measures:

  Reorient or relocate the receiving antenna.                                                              
  Increase the separation between the equipment and the receiver.

  Connect the equipment into an outlet on a circuit different from    

that to which the receiver is connected.

  Consult the dealer or an experienced radio/TV technician   

 

for help.

This device complies with Part 15 of the FCC Rules. Operation is subject to the 

following two conditions: 
1.   This device may not cause harmful interference. 
2.   This device must accept any interference received including interference 

that may cause undesired operation.

Industry Canada Compliance Statement

This device complies with Industry Canada license-exempt RSS standard(s). 

Operation is subject to the following two conditions:
1.   This device may not cause harmful interference.
2.   This device must accept any interference received including interference 

that may cause undesired operation.

Cet appareil est conforme avec Industrie Canada exempts de licence standard 

RSS (s). Son fonctionnement est soumis aux deux conditions suivantes:

1.   Ce dispositif ne peut causer des interférences nuisibles.
2.   Cet appareil doit accepter toute interférence reçue y compris des 

interférences qui peuvent provoquer un fonctionnement indésirable

.

FEDERAL COMMUNICATIONS COMMISSION NOTICE

DECLARATION OF CONFORMITY (DOC)

The Declaration of Conformity for this product can be found on the RTI website 

at:  www.rticorp.com/declaration

Summary of Contents for Cool Power CP-16i





























Reviews: