RTA 460EC-NNA4 Product User Manual Download | Manualshive

Page: 21 / 59

background image

Real Time Automation, Inc.

21

1-800-249-1612

Mapping - Transferring Data Between Devices

There are 5 ways to move data from one protocol to the other. You can combine any of the following
options to customize your gateway as needed.

Option 1

–

Data Auto-Configure Mappings:

The gateway will automatically take the data type (excluding

strings) from one protocol and look for the same data type defined in the other protocol.

If there isn’t a

matching data type, the gateway will map the data to the largest available data type. See Data Auto-
Configure section for more details.

Option 2

–

String Auto-Configure:

The gateway will automatically take the string data type from one

protocol and map it into the other. See String Auto-Configure section for more details.

Option 3

–

Manual Configure Mappings:

If you don’t want to use the Auto

-Configure Mappings

function, you must use the manual mapping feature to configure translations.

Option 4

–

Manipulation/Scaling:

You can customize your data by using math operations, scaling, or bit

manipulation. See Data Mapping-Explanation section for more details.

Option 5

–

Move Diagnostic Information:

You can manually move diagnostic information from the

gateway to either protocol. Diagnostic information is not mapped in Auto-Configure Mappings Mode.
See Diagnostic Info section for more details.

Going from Manual Mapping to Auto-Mapping will delete ALL mappings and
manipulations configured.

«
...
19
20
21
22
23
...
»

Summary of Contents for 460EC-NNA4




























































Reviews:

No comments

Related manuals for 460EC-NNA4

Brand: ABB Pages: 44

Brand: Duemmegi Pages: 11

Brand: NetComm Wireless Pages: 28

Brand: HMS Pages: 74

Brand: Rotel Pages: 146

MediaPack 1 Series

Brand: AudioCodes Pages: 10

MediaPack MP-112

Brand: AudioCodes Pages: 622

ZoomTel ADSL X5v 5585

Brand: Zoom Pages: 2

Brand: Wisen Pages: 12

Brand: wowvision Pages: 145

Brand: Nexotek Pages: 61

HomeConnect 3CRWE50194

Brand: 3Com Pages: 2

OfficeConnect 3CRWE554G72

Brand: 3Com Pages: 126

Brand: RadiSys Pages: 198

Brand: Tainet Pages: 225

Brand: Haltian Pages: 12

Brand: Zennio Pages: 37

NX-S/O 2 Series

Brand: call4tel Pages: 42

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands