RPE DIG Series Programming Instruction Manual Download Page 11

Page: 11 / 32

Press key

[+]

to select PM and

[-]

to set AM.

Press

CONFIRM

to pass to the following

item.

CONFIRM

: confirms the value and passes to

the following item (calendar).

NEXT

: disabled.

[+]

selects PM (icon PM on).

[-]

selects AM (icon AM on).

When the display flashes, use keys

[+]

and

[-]

to set the current day (1-7). Press

CONFIRM

to end the procedure.

CONFIRM

: confirms the value and exit from

the procedure (default screen).

NEXT

: disabled.

[+] / [-]

: increases and decreases the value to

be programmed.

PROGRAMMING PM/AM

PROGRAMMING THE

WEEKLY CALENDAR

The main screen is displayed when the clock

programming procedure is completed.

CONFIRM

: enters the clock programming

procedure.

NEXT

: main menu check.

In this screen, the keys

and

–

are disabled.

HOW TO EXIT FROM

CLOCK PROGRAMMING

PROCEDURE

Programmatore_serie_DIG_GB.indd 11

18/07/12 15.06

Summary of Contents for DIG Series

































Search results

Summary of Contents for DIG Series

Reviews:

Related manuals for DIG Series

Brands by name

Popular brands

RPE DIG Series, Programming Instruction Manual

Search results

Summary of Contents for DIG Series

Reviews:

Related manuals for DIG Series

Brands by name

Popular brands