background image

the rinsing tray and in the underlying 
filter mat. 
Grease and oily dirt is rinsed into the 
base unit and is then degraded by the  
microbes into carbon dioxide and 
water. 
 
 

 

Please read the operating 
instructions for your machine 
before using it, and pay particular 
attention to the following safety 
instructions. 

Warning and information plates on 
the machine provide important 
directions for safe operation. 

In addition to the information 
contained in the operating 
instructions, all statutory safety 
and accident prevention 
regulations must be observed. 

 
 
 
 

The voltage indicated on the type 
plate must correspond to the 
voltage of the electrical source.  

Safety class 1 

– Appliances may 

only be connected to sockets with 
proper earthing. 

It is recommended that you 
connect this device to a socket 
that has a 30mARCD device to 
guard against earth leakage faults. 

Please use the mains cable fitted 
by the manufacturer; the same is 
also applicable when you replace 
the cables. 

Never touch the mains plug with 
wet hands. 

Make sure that the power cord or 
extension cables are not damaged 
by running over, pinching, 
dragging or similar. Protect the 
cable from heat, oil and sharp 
edges. 

The extension cable must have a 
conductor cross section area of 
2.5mm and be protected against 
spraying water. The connection 
must not lie in water. 

If the power cord is replaced the 
control box cover must be 
correctly refitted to ensure that it is 
water tight. 

 
 
 
 

The machine must be checked 
prior to use to ensure that it is in 

proper working order and is 
operating safely. 

The machine must not be used in 
hazardous locations. 

The appliance must be sited on 
stable ground. 

All electrical equipment in the 
working area must be protected 
against any spraying cleaning 
solution. 

Please wear appropriate safety 
gear when using the machine- 
such as safety goggles and 
protective gloves. 

Do not use the Smartwasher™ to 
clean materials containing 
asbestos or other hazardous 
substances such as pesticides. 

Only use the cleaning solutions 
approved by the manufacturer. 

If the cleaning solution comes into 
contact with the eyes, please rinse 
the eyes thoroughly with water. If 
swallowed please consult a doctor 
immediately. 

 
 
 
 

The operator must use the 
machine properly as instructed in 
this manual. The operator must 
pay attention to any surrounding 
hazards and consider those 
working around him when using 
the Smartwasher™. 

The machine should only be used 
by people who have been 
instructed in how to use it 
properly. The Smartwasher™ 
must not be operated by children. 

Never leave the machine 
unattended when the cleaning 
solution is running through the tap. 

 
 
 
Turn off the Smartwasher™ and 
unplug the connection to the electrical 
socket. Then empty the machine if you 
need to move or transport the 
Smartwasher™. Only transport when 
empty. 
 
 
 

Switch off the Smartwasher™ and 
unplug from mains socket before 
carrying out any maintenance on 
the machine. 

Please wear appropriate safety 
gear such as safety goggles and 
gloves. 

Safety Instructions 

Power Connection 

Application 

Proper Use 

Moving or Transporting 

Maintenance 

Summary of Contents for PCS25 Smartwasher











Reviews: