background image

18

• At the gas line access hole, use insulation to re-

pack the space around the gas pipe.

• Insert insulation from the outside of the fireplace and

pack the insulation tightly to totally seal between the

pipe and the outer casing.

The gas line should be

installed by a qualified

service technician.

Figure 11. Gas Supply Line

Step 8

Gas Pressure

Requirements

Pressure requirements for Royal gas fireplaces are

shown in the table below.

Pressure

Natural Gas

Propane

Minimum

5.0 inches

11.0 inches

Inlet Pressure

w.c.

w.c.

Maximum Inlet

14.0 inches

14.0 inches

Gas Pressure

w.c.

w.c.

Manifold

3.5 inches

10.0 inches

Pressure

w.c.

w.c.

A one-eighth (1/8) inch (3 mm) N.P.T. plugged tapping

is provided on the inlet and outlet side of the gas

control for a test gauge connection to measure the

manifold pressure.
The fireplace and its individual shut-off valve must be

disconnected from the gas supply piping system

during any pressure testing of the system at test

pressures in excess of one-half (1/2) psig (3.5 kPa).
The fireplace must be isolated from the gas supply

piping system by closing its individual shut-off valve

during any pressure testing of the gas supply piping

system at test pressures equal to or less than one-half

(1/2) psig (3.5 kPa).

USE A WRENCH ON 

SHUT-OFF VALVE WHEN 

TIGHTENING GAS LINE

GAS VALVE 

FLEX

CONNECTOR

MANUAL

SHUT-OFF VALVE 

Summary of Contents for R-3500TV


































Reviews: