Royal Enfield CONSTELLATION 1958 Workshop Maintenance Manual Download | Manualshive

Page: 88 / 106

background image

SECTION K6

Front Wheel

With Dual 6in. Brake

1. Removal from Fork

To remove the front wheel from the fork

place  the  machine  on  the  centre  stand  and  front
stand,  if  fitted,  or  alternatively  with  sufficient
packing  (about  2  in.)  beneath  each  side  of  the
stand  to  lift the  wheel  clear  of  the  ground  when
tilted  back  on  to  the  rear  wheel.  Slacken  brake
cable  adjustments  and  disconnect  cables  from
handlebar  lever  and  from  operating  cam  levers
on hub. Unscrew the four nuts securing the fork
bottom tube lug caps (Part No. 38593) and allow
the wheel to drop forwards out of the front fork.
Make  sure  that  the  machine  stands  securely  on
the  rear  wheel  and  centre  stand-if  necessary
place  a  weight  on  the  saddle  or  a  strut  beneath
the fork to ensure this.

2. Removal of Brake Cover Plate Assemblies

Lock the brake "on" by pressure on the

operating lever, 38905 (R.H.) or 38906 (L.H.),

and  unscrew  the  cover  plate  nuts  31347.  The
right  and  left  hand  cover  plate  assemblies  can
then  be  withdrawn  from  the  respective  brake
drums.

3. Removal of Brake Shoes and Springs

This is best done by unscrewing the pivot pin

locknuts,  28715,  and  the  operating  lever  nuts,
10314, after which the assembly of brake shoes,
return  springs,  pivot  pin  and  operating  cam  can
be removed from the cover plate by light blows
with a hammer and drift on the ends of the pivot
pin and the operating cam, see Fig. 2. The return
springs,  29236,  can  then  be  unhooked  from  the
spring posts in the brake shoes thus allowing the
whole assembly to fall apart.

4. Replacing Brake Linings

Brake linings are supplied either in pairs

ready drilled complete with rivets or ready
fitted to service replacement brake shoes.

Section K6 Page 1

www.hitchcocksmotorcycles.com

«
...
86
87
88
89
90
...
»

Summary of Contents for CONSTELLATION 1958











































































































Reviews:

No comments

Related manuals for CONSTELLATION 1958

Brand: R&G Pages: 14

Brand: Honda Pages: 110

Brand: Honda Pages: 325

Brand: KTM Pages: 7

Brand: Arai Pages: 15

Road Sofa H18-07-18X all

Brand: Saddlemen Pages: 2

Brand: RIEJU Pages: 34

Brand: Baotian Pages: 30

Brand: BUMOT Pages: 5

Brand: HYOSUNG Pages: 100

Brand: HYOSUNG Pages: 96

Brand: Benelli Pages: 30

Brand: Benelli Pages: 51

Brand: Benelli Pages: 51

PowerParts 44011076140

Brand: KTM Pages: 17

Brand: APRILIA Pages: 153

Brand: Caberg Pages: 20

Brand: Zero Motorcycles Pages: 146

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands