Royal Enfield CONSTELLATION 1958 Workshop Maintenance Manual Download Page 11 | Manualshive

Page: 11 / 106

background image

The ports in the housing are connected as follows

W - delivery to rocker gear.

Y - suction from oil tank.

X - delivery to big ends.

Z - suction from oil tank.

Position 1.

The plunger A is being drawn out of

the cylinder hole in the disc C by the action of the peg
B on the shaft D. The port T in the disc C registers
with the suction port Y in the housing, so that oil is
drawn into the cylinder from the oil tank. At the same
time the delivery port W in the housing is uncovered
and oil below the disc in the housing is forced through
W to the rocker gear.

Position 2.

The plunger A is being pushed into the

cylinder  hole  in  the  disc  C.  The  port  T  in  the  disc
now registers with the delivery port X in the housing,
so  that  oil  is  forced  out  of  the  cylinder  to  the  big
ends.  At  the  same  time  the  suction  port  Z  in  the
housing  is  uncovered  and  oil  is  drawn  into  the
housing below the disc from the oil tank.

The ports in the housing are connected as follows :

W' - delivery to oil tank.

Y' - suction from crankcase.

X' - delivery to oil tank.

Z' - suction from timing chest.

Position 2.

The plunger A' is being pushed into the

cylinder  hole  in  the  disc  C'.  The  port  T'  in  the  disc
now registers with the delivery port X' in the housing,
so that oil is forced out of the cylinder back to the oil
tank.  At  the  same  time  the  suction  port  Z'  in  the
housing  is  uncovered  and  oil  is  drawn  into  the
housing below the disc from the timing chest.

Position 1.

The plunger A' is being drawn out of

the  cylinder  hole  in  the  disc  C'  by  the  action  of  the
peg  B'  on  the  shaft  D'.  The  port  T'  in  the  disc  C'
registers  with  the  suction  port  Y'  in  the  housing,  so
that oil is drawn into the cylinder from the crankcase
sump.  At  the  same  time  the  delivery  port  W'  in  the
housing  is  uncovered  and  oil  below  the  disc  in  the
housing is forced through W' back to the oil tank.

Section B4 Page 4

www.hitchcocksmotorcycles.com

«
...
9
10
11
12
13
...
»

Summary of Contents for CONSTELLATION 1958











































































































Reviews:

No comments

Related manuals for CONSTELLATION 1958

Zero S Series 2014

Brand: Zero Motorcycles Pages: 128

Pulsar 135 BS VI

Brand: Bajaj Pages: 48

Brand: GAS GAS Pages: 107

Brand: NEO TOOLS Pages: 8

Brand: KTM Pages: 207

Brand: Yamaha Pages: 276

R 1200 R Classic

Brand: BMW Pages: 1

Brand: Suzuki Pages: 80

Brand: hepco & becker Pages: 2

Brand: Shad Pages: 12

Brand: IBEX Pages: 3

Brand: APRILIA Pages: 216

Brand: Chicago Electric Pages: 7

Brand: Chicago Electric Pages: 10

Super Meteor 650

Brand: Royal Enfield Pages: 124

Brand: Bike Shield Pages: 4

Brand: Sealey Pages: 3

Brand: RIEJU Pages: 116

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands