Royal Enfield CONSTELLATION 1958 Workshop Maintenance Manual Download Page 18 | Manualshive

Page: 18 / 106

background image

The ports in the housing are connected as follows

W - delivery to rocker gear.

Y - suction from oil tank.

X - delivery to big ends.

Z - suction from oil tank.

Position 1.

The plunger A is being drawn out of

the cylinder hole in the disc C by the action of the peg
B on the shaft D. The port T in the disc C registers
with the suction port Y in the housing, so that oil is
drawn into the cylinder from the oil tank. At the same
time the delivery port W in the housing is uncovered
and oil below the disc in the housing is forced through
W to the rocker gear.

Position 2.

The plunger A is being pushed into the

cylinder  hole  in  the  disc  C.  The  port  T  in  the  disc
now registers with the delivery port X in the housing,
so  that  oil  is  forced  out  of  the  cylinder  to  the  big
ends.  At  the  same  time  the  suction  port  Z  in  the
housing  is  uncovered  and  oil  is  drawn  into  the
housing below the disc from the oil tank.

The ports in the housing are connected as follows :

W' - delivery to oil tank.

Y' - suction from crankcase.

X' - delivery to oil tank.

Z' - suction from timing chest.

Position 2.

The plunger A' is being pushed into the

cylinder  hole  in  the  disc  C'.  The  port  T'  in  the  disc
now registers with the delivery port X' in the housing,
so that oil is forced out of the cylinder back to the oil
tank.  At  the  same  time  the  suction  port  Z'  in  the
housing  is  uncovered  and  oil  is  drawn  into  the
housing below the disc from the timing chest.

Position 1.

The plunger A' is being drawn out of

the  cylinder  hole  in  the  disc  C'  by  the  action  of  the
peg  B'  on  the  shaft  D'.  The  port  T'  in  the  disc  C'
registers  with  the  suction  port  Y'  in  the  housing,  so
that oil is drawn into the cylinder from the crankcase
sump.  At  the  same  time  the  delivery  port  W'  in  the
housing  is  uncovered  and  oil  below  the  disc  in  the
housing is forced through W' back to the oil tank.

Section B11 Page 5

www.hitchcocksmotorcycles.com

«
...
16
17
18
19
20
...
»

Summary of Contents for CONSTELLATION 1958











































































































Reviews:

No comments

Related manuals for CONSTELLATION 1958

PAMPERA 400 - 2006

Brand: GAS GAS Pages: 70

Brand: KEDO Pages: 2

Brand: KEDO Pages: 3

Brand: KEDO Pages: 2

Brand: Yamaha Pages: 662

Brand: Yoshimura Pages: 3

Brand: Sharper Image Pages: 4

Brand: A.J.S. Pages: 104

Brand: RPS Pages: 28

Brand: Yamaha Pages: 110

Brand: R&G Pages: 9

Brand: DYNATEK Pages: 8

Brand: KTM Power Parts Pages: 22

Brand: KTM Power Parts Pages: 12

Brand: KTM Pages: 7

Brand: KTM Pages: 16

125 EXC EU 2014

Brand: KTM Pages: 27

2010 250 EXC-F AUS

Brand: KTM Pages: 125

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands