Rover HD TAB 900, User Manual

Page: 73 / 84

73
TV & SAT MEMORY PLAN UPGRADES
MEM PLANS UPGRADES:
Once you have identified and downloaded the correct ROVER S.M.A.R.T. PRO program on your PC ( for more
information, read the respective S.M.A.R.T. page in this user guide ), install it on your PC in order to load the
Memory Plans in your Meter. The proceed as follows:
• Once you have accessed the Update SW Area, identify the exact Model/Name of your Meter and click
on the corresponding picture;
• Click on the relative file: “Plans and Satellites” and download it on your PC.
WARNINGS
:
• Before carrying out your Meter’s Memory Plan upgrades, we suggest you close all the applications that
are active on your computer: e-mail messages, internet, management programs, etc.
• Also check that the Meter’s batteries are charged and that the Meter is connected to the mains. Most
importantly do not turn off or disconnect the Meter from the mains during the upgrade.
N.B. If the graphic bar showing the upgrade advancement blocks, do not interrupt the procedure
because the Memory Plan Upgrade is still taking place even if the PC monitor does not correctly show the
advancement in sequence.
PROCEDURE:
1. Connect your Meter to the mains and turn it on;
2. Wait for the Start Up phase of the Meter to finish correctly;
3. Connect the USB cable, first to the Meter and then to the PC;
4. Make sure that you have installed the PRO Version and start up the ROVER S.M.A.R.T. program in your PC;
5. In the ROVER S.M.A.R.T. PRO program window, click on “Instrument” followed by “Connect Instrument”;
6. Click on “Tools”, then “Mem” e and then “Open Mem” In the ROVER S.M.A.R.T. PRO program window;
7.
In the Open window, select the ”Memory Plan ( .mem )” downloaded from the Update SW Area;
8. Click on “Open” and confirm the selection;
9. Click on “Tools”, then “Mem” and then “Write Mem to Instruments”;
10. The following message will appear: WARNING: This operation will delete all the previous plans stored in
the meter;
11. Click on “OK” and confirm to start the upgrade;
12. Wait a few minutes, the ROVER S.M.A.R.T. PRO program will load the new Memory Plans in your Meter;
13. Once the download has been completed, the following message will appear: Plan Memory download
succesfully !.
WARNING:
In the case the update is interrupted or is not successful, check the USB cable connection and repeat the
procedure from the beginning.
If the procedure described in this paragraph continues to fail, contact the ROVER After Sales and Service
Department:
• e-mail: wecare@roverinstruments.com
• Fax: +39 030 990 68 94
It is possible to download the Software Upgrade Procedure directly from the ROVER website at the following
address: www.roverinstruments.com. Please refer to the section ”F.A.Q.”.
BATTERY AUTONOMY:
The battery autonomy is up to 3 hours maximum.
This device contains a built-in Li-PO (Lithium polimer) battery that can be recharged many times.
The battery contains chemicals that might wear with time even if not used. Please dispose of batteries
properly.
Do not take the battery pack apart or expose it to extreme temperatures (over 50°C). If the device has
been exposed to very low or high temperatures let it rest at room temperature before use.
The Battery must be recharged at room temperature (about 20°C) with the device turned off.
To avoid premature failure of the battery never leave the device with an empty battery for prolonged
periods.
RECHARGEABLE BATTERY __________________
RECHARGING THE BATTERY ________________
WARNINGS
IMPORTANT:
• DO NOT LEAVE THE BATTERIES DISCHARGED FOR LONG PERIODS;
• ALWAYS CHARGE THE BATTERIES AT NIGHT, EVEN IF THEY ARE NOT COMPLETELY DISCHARGED.
USEFUL INFORMATION:
1. The batteries supplied are high quality and tested individually, the autonomy depending on
the following conditions:
• the LNB power consumption: Single, Dual or Quadruple;
• the external temperature: with temperatures of less than 10°C, 20% of the capacity is lost;
• the age of the batteries: a 10% loss in effi ciency each year;
• Remember that the TIMER OFF function, that automatically turns off the Meter after
5 o 10 minutes of inactivity saves up to 30%.
2. The battery indicator has a tolerance ( like all battery powered electronic devices ) according
to the following factors:
• the battery’s charging percentage;
• external temperatures;
• battery wear and tear;
• +/– 2%
.
ICONS SHOWING THE BATTERY CHARGE STATUS:
LI-ION POLIMER BATTERIES