background image

5

S

ection

 2 — i

mportant

 S

afe

 o

peration

 p

racticeS

3. 

Before cleaning, repairing, or inspecting, stop the engine 

and make certain the impeller and all moving parts have 

stopped. Disconnect the spark plug wire and ground it 

against the engine to prevent unintended starting.

4. 

Do not change the engine governor settings or overspeed 

the engine. The governor controls the maximum safe 

operating speed of the engine.

5. 

Maintain or replace safety and instruction labels, as 

necessary.

6. 

Follow this manual for safe loading, unloading, 

transporting, and storage of this machine.

7. 

Never store the machine or fuel container inside where 

there is an open flame, spark or pilot light such as a water 

heater, furnace, clothes dryer, etc.

8. 

Allow machine to cool at least 5 minutes before storing.

9. 

Always refer to the operator’s manual for proper 

instructions on off-season storage.

10.  If the fuel tank has to be drained, do this outdoors.
11. 

Observe proper disposal laws and regulations for gas, oil, 

etc. to protect the environment.

12.  According to the Consumer Products Safety Commission 

(CPSC) and the U.S. Environmental Protection Agency (EPA), 

this product has an 

Average Useful Life

 of seven (7) years, 

or 60 hours of operation. At the end of the 

Average Useful 

Life

  have the machine inspected annually by an authorized 

service dealer to ensure that all mechanical and safety 

systems are working properly and not worn excessively. 
Failure to do so can result in accidents, injuries or death.

Do not modify engine

To avoid serious injury or death, do not modify engine in any 

way. Tampering with the governor setting can lead to a runaway 

engine and cause it to operate at unsafe speeds. Never tamper 

with factory setting of engine governor.

Notice Regarding Emissions

Engines which are certified to comply with California and federal 

EPA emission regulations for SORE (Small Off Road Equipment) 

are certified to operate on regular unleaded gasoline, and 

may include the following emission control systems: Engine 

Modification (EM), Oxidizing Catalyst (OC), Secondary Air 

Injection (SAI) and Three Way Catalyst (TWC) if so equipped.

Spark Arrestor

WARNING: 

This machine is equipped with an 

internal combustion engine and should not be used 

on or near any unimproved forest-covered, 

brushcovered or grass-covered land unless the 

engine’s exhaust system is equipped with a spark 

arrestor meeting applicable local or state laws (if 

any).

If a spark arrestor is used, it should be maintained in effective 

working order by the operator. In the State of California the 

above is required by law (Section 4442 of the California Public 

Resources Code). Other states may have similar laws. Federal laws 

apply on federal lands. 

A spark arrestor for the muffler is available through your 

nearest engine authorized service dealer or contact the service 

department, P.O. Box 361131 Cleveland, Ohio 44136-0019.

Summary of Contents for CS454R Series





















Reviews: