Roth EcoDWT plus 3 Installation Instructions Manual Download Page 35 | Manualshive

Page: 35 / 37

Roth EcoDWT plus 3 Installation Instructions Manual Download Page 35

Ins

ta

lla

tio

n I

ns

tru

cti

ons

Roth North America PO Box 245 Syracuse, NY 13211 1.888266.7684 www.roth-america.com

Install Instructions - Kits

5

|

P

a

g

e

Lube Installation Kit with Emergency Vent - Open or Closed Version

The EMERGENCY VENT KIT is to be used in installations in jurisdictions where tank emergency venting is required and an
open normal vent is acceptable.

INSTALLATION KIT - EMERGENCY VENT

(Includes emergency vent, hinged lockable fill cap, field adjustment
gauge PLUS either a metal mushroom cap with nipple (Open Version
EVO) or normally closed (NC) pressure vacuum vent (Closed Version EVC)

Lube Installation Kit - EVO - for all tank sizes

2315002106

Lube Installation Kit - EVC - for all tank sizes

2315002107

Note: Some installations may require a normally closed normal vent vs. an open vent cap. This vent opens
when the tank is being filled to avoid tank pressurization and also opens when the tank contents are being
pumped out to avoid vacuum accumulation. Otherwise it is closed, preventing infiltration of contamination
from outside the tank and evaporation of the tank contents.

Fill Cap
The fill cap includes a locking tab that may be fitting with a padlock for extra security if desired. It is
advantageous if it is mounted near the point of closest access to the tank for ease of filling. It installs directly
into a metallic adapter with thread sealant, tighten to 10-15 ft. lbs.

«
...
33
34
35
36
37
»

Summary of Contents for EcoDWT plus 3






































Reviews:

No comments