manualshive.com logo in svg

Roth EcoDWT plus 3, Installation Instructions Manual

Share
Download
Roth EcoDWT plus 3 Installation Instructions Manual Download Page 27

 

Roth  Industries and Roth Global Plascs  PO Box  245, Syracuse, NY 13211  PH (888)266-7684  FAX (315) 475-0200        www.roth-america.com 

Product Installaon Instrucons 

Roth DWT Lube Oil Tanks-Hose Reel Bracket Mounng Instrucons 
IV Hose Reel Mounng 

The Roth Hose Reel Bracket is predrilled to accept selected Hose Reel models manufactured by Balcrank and Zee Line/
Naonal-Spencer.  Other models and manufacturers can be mounted on the Roth Hose Reel Bracket by drilling the 
bracket in the field to match specific mounng requirements (Figure 8)  
 

CAUTION-Whenever Hose Reels are mounted on the Roth DWT Oil Storage Tank, tank e down kits are required to 
avoid spills and risk of personal injury due to tank p-over.   

 
 

 
 
 
 
 
 
 
 
 
 
 
 
 
 
V Pump and Accessory Mounng 

Pumps, fluid meters, and other lube related accessories may be mounted on the Roth Hose Reel Bracket. The total 
equipment weight mounted on a single tank should not exceed 100lbs/45Kg.  
 
 

Please contact Roth Technical Department using the contact informaon below with any quesons.   

Fig 8 

HRBINST 13015 

Fig 8 

Summary of Contents for EcoDWT plus 3






































Reviews:

No comments

Brands by name

Popular brands

Load more brands