Roswell Bennington C924-016650 Care, Maintenance, Operations Download Page 5

Page: 5 / 18

Tower Bimini

Care / Maintenance / Operation

Rev. 16-Aug-18

If you have any questions please call : 1-321-638-1331

Information:

[email protected]

***Important***

Read & follow these instructions carefully. Failure to do so may result in damage to parts.

Damage to parts from improper use is not covered under warranty.

GENERAL BIMINI CARE & MAINTENANCE

Check all bimini hardware before every use on the water. We recommend keeping a set of Allen

wrenches on your boat for this purpose. Verify that all bolts are tight. Even with threadlocker they

may loosen over time.

Watch your head when walking under the tower & bimini.

NEVER USE CLEANERS ON YOUR BIMINI FRAME!

The Bennington Tower Bimini is designed with materials and finishes that resist the

elements. A mild soap and water combination may be used to remove traveling grime or

water spots on the metal components. Use only a soft cloth and never use any chemical

cleaners. Clean after each use.

For more info on how to clean and care for your Sunbrella Fabric please go to :

http://www.sunbrella.com/en_us/how/cleaning/marine-tops-covers.php

Summary of Contents for Bennington C924-016650


















