background image

FOLDING 

& LOWERI

NG THE 

TOWER IS 

A TWO P

ERSON 

OPERATION. 

BEFORE U

NLOCKING 

THE TOWER

 ENSURE S

OMEONE IS

 

READY TO 

HELP FOLD 

THE TOWER 

SAFELY. 

INSERT LE

VER TO U

NLOCK T

OWER.   

TURN LE

VER CLOC

KWISE UNTI

L IT STOP

S.  

THIS IS THE R

ESET POSI

TION. TO 

LOCK TOWER

,  

INSERT L

EVER AND 

TURN COU

NTERCLOCK

WISE.

WHEN TOWER IS

 UPRIGHT

,

SAFETY HA

NDLES M

UST BE 

INSTALLED

ONLY REMOVE HAND

LES TO FOL

D & 

LOWER T

OWER.

4

Bennington Tower Care/ Maintenance/ Operations

www.roswellmarine.com

D

E

Raise the tower up

F

Folding Your Tower

With both latches released, slowly lower the 

tower until it rests at the stop position.

This folded position is intended for low speed 

boat operation such as 

- Parking boat in garage

- Boating under a bridge

- Parking Boat in Slip

To raise the tower up repeat steps B, C, D & E in reverse.

Fold the tower down

DO NOT TRAILER YOUR TOWER IN THE FOLDED POSITION 

1

2

3

Adjust the fold limit

To adjust the fold 

height limit, rotate 

both handles to 

desired distance 

ensuring that nothing 

hits the tower before 

the handles contact 

the rubber on the 

folding blocks.

Repeat this for

both sides.

FOLDING 

& LOWERING THE 

TOWER IS A TWO PERSON 

OPERATION. BEFORE UNL

OCKING 

THE TOWER ENSURE SOMEONE IS 

READY TO HELP FOLD THE 

TOWER SAFELY. 

INSERT LEVER TO UNLOCK 

TOWER.   

TURN LEVER CLOCKWISE UNTIL

 IT STOPS.  

THIS IS THE RESET POSITION. 

TO LOCK TOWER,  

INSERT LEVER AND TURN 

COUNTERCLOCKWISE.

WHEN TOWER IS UPRIGHT

,

SAFETY HANDLES MUST BE 

INSTALLED. 

ONLY REMOVE HANDLES 

TO FOLD & 

LOWER TOWER.

Safety 

Handle

Latch 

Lever

Instruction 

Decal

Summary of Contents for Bennington C924-016650



















Reviews: