O
PERATING
I
NSTRUCTIONS
XII. GlobalCruise OPERATING
INSTRUCTIONS
ON
: To operate the
GlobalCruise
, turn the power
button
ON
.
(
Green LED Indicator
will light, if
equipped.)
Wait three
(3)
seconds before setting
speed.
SET SPEED
: To engage system, drive at any speed
above
50 KPH
(33 MPH)
, press
SET/COAST
or
press
RESUME/ACCEL
and release, then remove
your foot from the accelerator pedal. Automatic
control will be at the speed of the vehicle when the
button is released plus or minus
3 KPH
(1-1/2
MPH)
Press accelerator and speed will increase,
release accelerator and you will return to set
speed.
NOTE:
The
RESUME/ACCEL
button will
SET
the
GlobalCruise
without pressing the
SET
button first.
COAST
: Press and Hold the
SET/COAST
button
and your speed will decrease. Release button and
speed of vehicle at time button is released will be
new set speed if above
50 KPH
(33 MPH).
ACCEL
: Press and hold the
RESUME/ACCEL
but-
ton and your speed will increase. Release button
and you will have a new higher set speed.
TAP-UP
: You can gradually increase your speed by
quickly pressing and releasing the
RESUME/
ACCEL
button. Each time you press and release
the button your speed will increase by
1-1/2 to 5
KPH
(2 to 3 MPH).
TAP-DOWN
: You can gradually decrease your
speed by quickly pressing and releasing the
SET/COAST
button. Each time you press and
release the button your speed will decrease by
1-
1/2 to 5 KPH
(2 to 3 MPH).
DISENGAGE
: Depress brake pedal slightly; auto-
matic speed control will cease but set speed will
stay in the systems memory. Also, you can dis-
engage by pressing button to
OFF
position, but
this erases the memory. To get the
RESUME
fea-
ture to work again, you must first set a speed.
Turning
OFF
the ignition also clears the systems
memory.
RESUME
: After disengaging system with brake or
clutch, return to
SET
speed by driving above
50
KPH
(33 MPH)
. Then press
RESUME/ACCEL
but-
ton and release it. If acceleration rate is faster or
slower than you like, drive to within a few
KPH
(MPH)
of your set speed, then press and release
the
RESUME/ACCEL
button.
THINGS YOU SHOULD KNOW
ABOUT YOUR GlobalCruise
The performance of the
GlobalCruise
is dependent
upon the condition of the engine, its size and even
by the type of emission control equipment it has.
Driving at higher altitudes will have an effect on
GlobalCruise
performance.
Under normal conditions and with proper switch
settings, speed should be controlled within plus or
minus
3 KPH
(1-1/2 MPH)
. There may be situa-
tions; however, which make it seem as if the
GlobalCruise
is not capable of functioning accu-
rately, such as an extra heavy load, a very steep
hill, or a severe headwind.
CAUTION: Do not use the GlobalCruise on
a slippery road nor in heavy
traffic.
CAUTION:
(Manual Transmission)
While
driving with the GlobalCruise
ON, do not shift to neutral
without depressing the clutch
pedal, as this may cause
engine racing or overreving. If
this happens, depress the
clutch pedal or turn OFF the
main Cruise Control Switch
immediately.
OUR QUALIFIED EXPERT TECHNICAL SERVICE DEPARTMENT IS
READY TO ASSIST YOU WITH ANY QUESTIONS OR PROBLEMS
THAT YOU MAY HAVE ABOUT OUR PRODUCT. CONTACT US VIA
PHONE AT (910) 277-1828 (USA) OR FAX AT (910) 276-3759 (USA).
Page 24
