Rossmax CalPro Instruction Manual Download Page 2

2

3

 

Table of Contents:

Introduction  ...................................................................................... 3
Preliminary Remarks ........................................................................... 3
Cautionary Notes ............................................................................... 3
Name/Function of Each Part ............................................................ 4,5
LCD Display Explanations ................................................................... 6
Using the AC Adapter ........................................................................ 7
Connect Methods ........................................................................... 7,8
Operation Procedures
  1. Data link status operation  ........................................................... 9
  2. Readout Mode  .......................................................................... 10
  3. Auto Calibration Mode  ............................................................. 18
  4. Measurement Count Display Mode  ........................................... 20
  5. Measurement Count Clearance Mode  ....................................... 21
  6. Calibration Reminder Setting Mode  .......................................... 22
  7. Pressure Gauge Mode  .......................................................... 23-25
Change "mmHg" to "kPa" ............................................................. 26
Error Messages ................................................................................ 27

Specifications

 ................................................................................... 28

Safety Certifications

 ......................................................................... 29

USA FCC Class B ............................................................................. 29
Maintenance of ROSSMAX Calibrator .............................................. 29

 

Introduction 

The calibration system developed by Rossmax Reasearch and Develop-
ment is equipped with the following features :

● 

Automatic device pressure checking

● 

Automatic device pressure calibration

● 

Measurement count check and reset

● 

Digital manometer

Which helps our partners to offer on-site and prompt calibration service 

to end users as well as significantly enhance customer satisfaction!

 

Preliminary Remarks

The quality of the device has been verified and conforms to the provi

-

sions of the Electromagnetic Compatibility EMC Directive 2014/30/EU; 
Low Voltage Directive (LVD) 2014/35/EU and EN/IEC 61010-1 :2010 Safe-
ty requirements for electrical equipment for measurement, control, and 
laboratory use - Part 1: General requirements.

 

Cautionary Notes

1.  The unit contains high-precision assemblies. Therefore, avoid extreme 

temperatures, humidity, and direct sunlight. Avoid dropping or strong-
ly shocking the main unit, and protect it from dust.

2.  The unit should not be operated by children so to avoid hazardous 

situations.

3.  If the unit is stored near freezing, allow it to acclimate at room tem-

perature before use.

4.  This unit is not field serviceable. You should not use any tool to open 

the device nor should you attempt to adjust anything inside the de-
vice. If you have any problems, please contact the store or the doctor 
from whom you purchased this unit or please contact Rossmax Inter-
national Ltd.

5.  Dispose of device, batteries, components and accessories according to 

local regulations.

6.  Data link can only be connected with Rossmax blood pressure monitor 

and calibrator. It cannot be used for any other purpose.

7.  Clean the device carefully with a slightly damp, soft cloth.

Summary of Contents for CalPro


















Reviews: