manualshive.com logo in svg

Rosslare AY-Q64, Installation And Programming Manual

Share
Download
Rosslare AY-Q64 Installation And Programming Manual Download Page 24

Programming the AY-Q64 

24 

AY-Q64 Installation and Programming Manual 

2.

 

Press "

3

" to enter Menu 3. 

 

The Transmit LED turns red. 

 

3.

 

Enter the new 4-digit code you wish to 

set as the Programming code. 

 

One beep is emitted on success. 

 

The system returns to Transmit mode. 
The Program LED turns off and the 
Transmit LED remains red.

 

 

 

 

The Programming code cannot be erased; the code 0000 is not 
valid and does not erase the Programming code. 

6.6

 

14B

Changing the Facility Code 

To change the Facility code: 

1.

 

Enter Programming mode. 

 

2.

 

Press "

4

" to enter Menu 4. 

 

The Transmit LED flashes orange. 

 

3.

 

Enter the new 3-digit code you wish to 
set as the Facility code. 

 

One beep is emitted on success. 

 

The system returns to Transmit mode. 
The Program LED turns off and the 

Transmit LED turns red.

 

 

 

 

Transmit 

Program 

Red  Green 

 

Transmit 

Program 

Red 

 

 

Transmit 

Program 

 

Green 

 

Transmit 

Program 

Orange

 

Green 

 

Transmit 

Program 

Red 

 

Summary of Contents for AY-Q64































Reviews:

No comments

Brands by name

Popular brands

Load more brands