manualshive.com logo in svg

Rosslare AY-Q64, Installation And Programming Manual

Share
Download
Rosslare AY-Q64 Installation And Programming Manual Download Page 15

Programming the AY-Q64  

AY-Q64 Installation and Programming Manual 

15 

6.1

 

Entering Programming Mode 

To enter Programming mode: 

1.

 

Press the 

#

 key 4 times within 2 seconds. 

The Transmit LED turns off and the 
Program LED turns red. 

 

2.

 

Enter your 4-digit Programming code. 

 

If the Programming code is valid, the 

Program LED turns green and the AY-
Q64 enters Programming mode. 

 

 

 

•

 

The factory default Programming code is 1234. 

•

 

If a Programming code is not entered within 30 seconds, the AY-
Q64 returns to Transmit mode. 

6.2

 

Exiting Programming Mode 

To exit Programming mode at any time: 

1.

 

Press the 

#

 key. 

 

You hear 3 beeps. 
The Program LED turns off and the 

Transmit LED turns red. 

 

This indicates that the AY-Q64 has returned to Transmit mode. 
Wrong entries may reset the reader back to Transmit mode. 
While in Programming mode, if no key is pressed for 30 seconds, 
the AY-Q64 exits Programming mode and returns to Transmit 

mode. 

 

Transmit 

Program 

 

Red 

 

Transmit 

Program 

 

Green 

 

Transmit 

Program 

Red 

 

Summary of Contents for AY-Q64































Reviews:

No comments

Brands by name

Popular brands

Load more brands