Rosslare AC-C31V Installation Manual Download Page 30 | Manualshive

Page: 30 / 35

Rosslare AC-C31V Installation Manual Download Page 30

Programming the AC-C31V

AC-C31V Installation Manual

Page 28

12.12

Replacing a Lost Programming Code

Note:

In order to be able to replace a lost programming code, the
AC-C31V must be in Normal Mode. Before proceeding, verify

that the Mode LED is green.

1. Remove power from the AC-C31V.

2. Press the REX button.
3. Apply power to the unit while pressing the REX button.

4. Release the REX button.

5. Program a new Programming Code into the unit using the

initial default code 1234. You have 15 seconds to do so,
before the controller reverts to the existing code.

12.13

Replacing a Lost Normal/Secure Code

Note:

In order to be able to replace lost normal/secure code, the
AC-C31V must be in Secure Mode. Before proceeding, verify

that the Mode LED is red.

1. Remove power from the AC-C31V.

2. Press the REX button.

3. Apply power to the unit while pressing the REX button.
4. Release the REX button.

5. Program a new Normal/Secure Code into the unit using the

initial default code 3838. You have 15 seconds to do so,

before the controller reverts to the existing code.

«
...
28
29
30
31
32
...
»

Summary of Contents for AC-C31V




































Reviews:

No comments