manualshive.com logo in svg

Ross TES9, Software User Manual

Share
Download
Ross TES9 Software User Manual Download Page 44

6–2 • Constant Data Module

TES9 Software User Manual (Iss. 04)

Configuration

When a Constant Data module is selected for configuration in the main TES9Set menu.

Each of the menu items is described in the following sections.

Data IDs

The Data ID and Secondary Data ID specify the hexadecimal values to be used for the 
corresponding fields in the encoded Ancillary Data Packet, as defined by SMPTE 291M.

Line Selection

For Line Selection, radio buttons are used to select the chroma or luma channel. The VANC line 
is selected using a pull down list.

Constant Data

Currently, four types of constant data are supported, as follows:

• Audio Metadata for Stereo 2+2
• Audio Metadata for 5.1 Surround
• Audio Metadata for Stereo 2+2 with SAP
• Audio Metadata for 5.1 Surround with SAP

Clicking on the radio button selects the type of metadata. Clicking on None disables the Constant 
Data Module.

Conditional Insertion

If this check box is not checked, then the Constant Data will always be inserted, and any upstream 
VANC packets with the same DID/SDID will be deleted.

If this check box is checked, then the Constant Data will only be inserted if there is not already an 
upstream VANC packet with the same DID/SDID. Therefore, if there is an upstream VANC 
packet with the same DID/SDID, it will be allowed to pass through and the new constant data will 
not be inserted.

Note

 — TES9 containing software with part number 36-10607-01 revision A or B do not 

support the last two constant data types in the above list or the Conditional Insertion 
feature. When TES9Set is being used to configure TES9s containing one of these two 
versions of software, the Constant Data Module Configuration menu will only contain the 
features that are available.

Summary of Contents for TES9





































































Reviews:

No comments

Brands by name

Popular brands

Load more brands