background image

9

Fuel and Lubrication Cont …...

WARNING!: 

Never use raw fuel with out oil in your unit. This will cause permanent 

engine damage and void the your warranty for that product. Never use a fuel mix-

ture that has been stored for over 90 days.

WARNING!:  

The 2 stroke oil must be a premium grade oil for 2-cycle air cooled 

engines and must be mixed at a 25:1 ratio with the fuel.  Mixing the fuel at a greater 

ration than 25:1 provides insufficient lubrication and will cause  engine damage and 

voids your engines warranty.

Motor

Regular Unleaded Plus 2 

stroke oil. Mixed 25:1

Chain

Use Chain 

saw chain oil

Lubrication of chain and chain bar

Whenever you refill the fuel tank with petrol you must also top up the level of chain 

oil in the chain oil tank. It is recommended to use standard chain oil.

SAW CHAIN / BAR LUBRICATION

Adequate lubrication of the saw chain is essential at all times to minimize friction with the 

guide bar.

Never starve the bar and chain of oil. Running the saw with too little oil will decrease cutting 

efficiency, shorten saw chain life, cause rapid dulling of chain, and cause excessive wear of bar 

from overheating. Too little oil is evidenced

by smoke, bar discolouration or pitch build-up. New chains/bars should be lubricated by hand 

before starting.

AUTOMATIC OILER

Your chain saw is equipped with an automatic  oiler system. The oiler automatically delivers 

the proper amount of oil to the bar and chain. As the engine speed increases, so does the oil 

flow to the bar pad. The oil tank should be checked and topped up each time the fuel tank is 

refilled.

Check the operation of the oil pump by running the saw at a medium speed. There 

should be visible spatters of oil coming from tip of the saw about 30 second after 

starting the saw.

WARNING: 

During normal operation the chain brake, clutch cover, bar and chain 

are lubricated with chain oil.  After use oil will drain for many weeks and pool on the 

surface underneath the chainsaw.

Place the chainsaw on a protected surface to contain the draining lubricating oil 

when not being used.

Summary of Contents for rgcs38cc





















Reviews: