manualshive.com logo in svg

Ross 4500DR-204-03, User Manual, Page: 45 / 70

Share
Download
Ross 4500DR-204-03 User Manual Download Page 45

ACO-4500 User Guide (v3.0)

Front Panel Menu System • 45

The Network Menu, and the associated sub-menus, allows the user to configure and control the behavior of the 
Ethernet system within the ACO-4500. Before proceeding, the user must contact their Network Administrator, and 
obtain suitable IP addresses, etc., that will need to be programmed within this menu.

IP Address

This menu line allows the user to enter the pre-determined IP address of the ACO-4500. The options in the 
sub-fields are: 000 through 255 where 000" is the default “no action” setting. 

To change the settings:

1. pressing the rotary control advances through each sub-field

2. rotating the rotary control changes the value of the currently selected sub-field.

SubNet Mask

This menu line allows the user to enter the pre-determined SubNet Mask address of the ACO-4500. 

The options in the sub-fields are: 000 through 255 where “000” is the default “no action” setting.

To change the settings

1. pressing the rotary control advances through each sub-field

2. rotating the rotary control changes the value of the currently selected sub-field.

Gateway

This menu line allows the user to enter the pre-determined Gateway address of the ACO-4500. Typically, this might 
be the IP address of a network hub to which the ACO-4500 is connected.

The options in the sub-fields are: 000 through 255 where “000” is the default “no action” setting.

To change the settings

1. pressing the rotary control advances through each sub-field

2. rotating the rotary control changes the value of the currently selected sub-field.

MAC Address

This menu line displays the MAC Address (Media Access Control), a unique, read-only identifier assigned to 
network interfaces for communications on the physical network segment.

This menu item cannot be changed - the MAC address is stored in a hardware device. This address is unique to each 
ACO-4500, and is also used to provide unique update keys when enabling options within the unit.

NTP, DashBoard, Backup Device

These menu lines provide access to the subsequent menu levels, as indicated. These are defined in the following 
sections.

DashBoard Menu

Figure 7.13

 provides and example of the Dashboard Menu.

Summary of Contents for 4500DR-204-03







































































Reviews:

No comments